decorflame MP4100-26 Anweisungen - Seite 2
Blättern Sie online oder laden Sie pdf Anweisungen für Innenkamin decorflame MP4100-26 herunter. decorflame MP4100-26 3 Seiten. Electric fireplace heater
Seite drucken
tHiS ElEctric FirEplacE HEatEr iS FOr USE ON 120 VOltS. tHE cOrD HaS a plUG aS
SHOwN at a iN illUStratiON BElOw. aN aDaptEr aS SHOwN at c iS aVailaBlE FOr
cONNEctiNG tHrEE-BlaDE GrOUNDiNG-typE plUGS tO twO-SlOt rEcEptaclES. tHE
GrEEN GrOUNDiNG plUG ExtENDiNG FrOM tHE aDaptEr MUSt BE cONNEctED tO a
pErMaNENt GrOUND SUcH aS a prOpErly GrOUNDED OUtlEt BOx. tHE aDaptEr SHOUlD
NOt BE USED iF a tHrEE-SlOt GrOUNDED rEcEptaclE iS aVailaBlE.
a 15 aMp circUit iS rEqUirED tO OpEratE tHiS FirEplacE HEatEr. iF tHE BrEakEr
tripS wHEN tHE FirEplacE HEatEr iS USED tHEN yOU May NEED tO MOVE tHE FirEplacE
HEatEr tO aNOtHEr lOcatiON Or UNplUG OtHEr appliaNcES tHat arE ON tHE SaME
circUit. iF yOU rEqUirE aN ExtENSiON cOrD USE ONE tHat iS ratED at 1875 wattS.
PARTS LIST
Z) WALL ANCHOR SAFETY CABLE
Wall anchor .................................................................................................................... 1
Screw for wall anchor .................................................................................................... 1
Screw for mantel ........................................................................................................... 1
Safety cable ................................................................................................................... 1
TOOL REQUIRED: PHILLIPS HEAD SCREWDRIVER
WALL ANCHOR SAFETY CABLE
The use of the wall anchor safety cable is highly recommended in order to reduce the risk
of the fireplace being tipped over accidentally.
warNiNG: tHiS caBlE May rEDUcE pOSSiBlE riSk OF iNJUry iF tHE FirEplacE iS
iMprOpErly HaNDlED, BUt iS NOt a SUBStitUtE FOr prOpEr aDUlt SUpErViSiON.
cHilDrEN SHOUlD NOt BE lEFt UNattENDED NEar aNy HEatEr.
1. Drill a 8 mm (5/16") hole in the wall. Insert the plastic wall anchor into the hole and
gently tap until the flange on the anchor is against the wall surface.
2. Position the back edge of the mantel close to the wall.
3. Attach the safety cable to the mantel using the screw for the mantel. See fig. A.
4. Use the screw for wall to attach the other end of safety cable to the wall.
5. Make sure all screws are tight.
Fig. A
OPERATION
After reading complete instructions, confirm all controls on fireplace are in the OFF
position. Plug the fireplace into a 15AMP/120Volt outlet. If the cord does not reach, you
may use an extension cord rated for a minimum of 1875 WATTS. Once the fireplace insert
has been properly connected to a grounded electrical outlet, it is ready to operate.
The controls are located behind the grill below the front glass and can be accessed by
pulling the grill from the top, forward and down.
warNiNG: DO NOt tOUcH. HOt SUrFacE at cENtEr OF Grill. HOlD lEFt Or riGHt SiDE
OF tHE Grill wHEN pUlliNG OUt.
O/i: Press this switch for main power and flame effect. The indicator light will turn on. See
below for other control instructions.
1250w: For heat function, press this switch while O/I switch is in the on position. The
indicator light will turn on.
temperature control: To adjust the temperature to your individual requirements, turn
the temperature control dial to the right (clockwise) to increase the desired tempera-
ture and to the left for lower temperature. This temperature control dial can only be
used while the O/I switch and 1250W switch are in the ON position.
NOtE: When the O/I switch is turned off, all other heater functions will stop even though
the switches may be in the on position.
NOtE: In order to shut down the heater safely, it is recommended to turn the temperature
control knob to lowest setting and allow the heater to cool down before pressing the O/I
switch to off position.
MAINTENANCE
warNiNG: DiScONNEct pOwEr aND UNplUG tHE pOwEr cOrD BEFOrE attEMptiNG aNy
MaiNtENaNcE Or clEaNiNG tO rEDUcE tHE riSk OF FirE, ElEctric SHOck Or DaMaGE
tO pErSONS. tHE BUlBS iN yOUr UNit caN BEcOME ExtrEMEly HOt.
Allow at least 10 minutes between turning off the unit and removing the light bulbs to
avoid the accidental burning of the skin.
riSk OF FirE: DO NOt ExcEED tHE rEcOMMENDED BUlB wattaGE.
2