decorflame MP4100-26 Talimatlar - Sayfa 2

Kapalı Şömine decorflame MP4100-26 için çevrimiçi göz atın veya pdf Talimatlar indirin. decorflame MP4100-26 3 sayfaları. Electric fireplace heater

Sayfayı Yazdır

tHiS ElEctric FirEplacE HEatEr iS FOr USE ON 120 VOltS. tHE cOrD HaS a plUG aS

SHOwN at a iN illUStratiON BElOw. aN aDaptEr aS SHOwN at c iS aVailaBlE FOr

cONNEctiNG tHrEE-BlaDE GrOUNDiNG-typE plUGS tO twO-SlOt rEcEptaclES. tHE

GrEEN GrOUNDiNG plUG ExtENDiNG FrOM tHE aDaptEr MUSt BE cONNEctED tO a

pErMaNENt GrOUND SUcH aS a prOpErly GrOUNDED OUtlEt BOx. tHE aDaptEr SHOUlD

NOt BE USED iF a tHrEE-SlOt GrOUNDED rEcEptaclE iS aVailaBlE.

a 15 aMp circUit iS rEqUirED tO OpEratE tHiS FirEplacE HEatEr. iF tHE BrEakEr

tripS wHEN tHE FirEplacE HEatEr iS USED tHEN yOU May NEED tO MOVE tHE FirEplacE

HEatEr tO aNOtHEr lOcatiON Or UNplUG OtHEr appliaNcES tHat arE ON tHE SaME

circUit. iF yOU rEqUirE aN ExtENSiON cOrD USE ONE tHat iS ratED at 1875 wattS.

PARTS LIST

Z) WALL ANCHOR SAFETY CABLE

Wall anchor .................................................................................................................... 1

Screw for wall anchor .................................................................................................... 1

Screw for mantel ........................................................................................................... 1

Safety cable ................................................................................................................... 1

TOOL REQUIRED: PHILLIPS HEAD SCREWDRIVER

WALL ANCHOR SAFETY CABLE

The use of the wall anchor safety cable is highly recommended in order to reduce the risk

of the fireplace being tipped over accidentally.

warNiNG: tHiS caBlE May rEDUcE pOSSiBlE riSk OF iNJUry iF tHE FirEplacE iS

iMprOpErly HaNDlED, BUt iS NOt a SUBStitUtE FOr prOpEr aDUlt SUpErViSiON.

cHilDrEN SHOUlD NOt BE lEFt UNattENDED NEar aNy HEatEr.

1. Drill a 8 mm (5/16") hole in the wall. Insert the plastic wall anchor into the hole and

gently tap until the flange on the anchor is against the wall surface.

2. Position the back edge of the mantel close to the wall.

3. Attach the safety cable to the mantel using the screw for the mantel. See fig. A.

4. Use the screw for wall to attach the other end of safety cable to the wall.

5. Make sure all screws are tight.

Fig. A

OPERATION

After reading complete instructions, confirm all controls on fireplace are in the OFF

position. Plug the fireplace into a 15AMP/120Volt outlet. If the cord does not reach, you

may use an extension cord rated for a minimum of 1875 WATTS. Once the fireplace insert

has been properly connected to a grounded electrical outlet, it is ready to operate.

The controls are located behind the grill below the front glass and can be accessed by

pulling the grill from the top, forward and down.

warNiNG: DO NOt tOUcH. HOt SUrFacE at cENtEr OF Grill. HOlD lEFt Or riGHt SiDE

OF tHE Grill wHEN pUlliNG OUt.

O/i: Press this switch for main power and flame effect. The indicator light will turn on. See

below for other control instructions.

1250w: For heat function, press this switch while O/I switch is in the on position. The

indicator light will turn on.

temperature control: To adjust the temperature to your individual requirements, turn

the temperature control dial to the right (clockwise) to increase the desired tempera-

ture and to the left for lower temperature. This temperature control dial can only be

used while the O/I switch and 1250W switch are in the ON position.

NOtE: When the O/I switch is turned off, all other heater functions will stop even though

the switches may be in the on position.

NOtE: In order to shut down the heater safely, it is recommended to turn the temperature

control knob to lowest setting and allow the heater to cool down before pressing the O/I

switch to off position.

MAINTENANCE

warNiNG: DiScONNEct pOwEr aND UNplUG tHE pOwEr cOrD BEFOrE attEMptiNG aNy

MaiNtENaNcE Or clEaNiNG tO rEDUcE tHE riSk OF FirE, ElEctric SHOck Or DaMaGE

tO pErSONS. tHE BUlBS iN yOUr UNit caN BEcOME ExtrEMEly HOt.

Allow at least 10 minutes between turning off the unit and removing the light bulbs to

avoid the accidental burning of the skin.

riSk OF FirE: DO NOt ExcEED tHE rEcOMMENDED BUlB wattaGE.