ALIBI ALI-CD700WAIR Installations- und Benutzerhandbuch - Seite 3
Blättern Sie online oder laden Sie pdf Installations- und Benutzerhandbuch für Sicherheitskamera ALIBI ALI-CD700WAIR herunter. ALIBI ALI-CD700WAIR 3 Seiten. Infrared mini dome camera
Seite drucken
VIDEO SETUP submenu:
•
BRIGHTNESS: Rock the joystick left or right to adjust the brightness of the video image.
—
CONTRAST: Rock the joystick left or right to adjust the contrast of the video image.
—
COLORGAIN: Rock the joystick left or right to adjust the color gain of the video image.
—
SHARPNESS: Rock the joystick left or right to adjust the sharpness of the video image
—
NR: Rock the joystick left or right to set the noise reduction to HIGH, MIDDLE, DEFAULT, or LOW.
—
MIRROR: Rock the joystick left or right to set the mirror effect (reflection) to HV (horizontal and
—
vertical reflection), H (horizontal reflection), or V (vertical reflection).
LANGUAGE: Select ENGLISH or CHINESE.
—
SYSTEM SETUP submenu:
•
OSD COLOR: Rock the joystick left or right to select either RED, WHITE or YELLOW.
—
OSD BG: Rock the joystick left or right to select either background ON or OFF.
—
FUNCTION SETUP submenu:
•
MOTION: Rock the joystick left or right to select the motion detection area (1 .. 5).
—
ALARM: Rock the joystick left or right to select either alarm ON or OFF. When ON, the motion
—
detection area flickers when motion is sensed in that area.
RESET submenu:
•
RESET: Select RESET to set the camera to it's factory default configuration.
—
SAVE & EXIT submenu:
•
SAVE & EXIT: Select SAVE & EXIT to save your settings and close the OSD menu system.
—
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
•
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
•
These may cause damage to the surface over time.
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
CAUTION
carefully follow the accompanying instructions.
Troubleshooting
Problem
Nothing appears on the screen
The video image is dim or not clear.
The screen is dark.
The camera is not working properly and the
surface of the camera is hot.
The image on the monitor flickers
www.observint.com
3
Possible Cause
- Check the power connection.
- Check the video signal cable connection to the monitor.
- If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
- Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
- Make sure that the camera isn't facing direct sunlight or fluorescent light.
If necessary,change the camera position.
Specifications
Parameter
Specification
Image Sensor
1/3" DIS
Signal System
NTSC
Effective Pixels
976 (H) × 496 (V)
Min. Illumination
0.1 Lux @ (F1.2, AGC ON), 0 Lux with IR
Shutter speed
1/60 s to 1/100,000 s
Lens
2.8 mm @ F2.2
Angle of view
68.4° (2.8 mm)
Lens Mount
M12
Angle Adjustment
Pan: 0 ~30°, Tilt: 0 ~ 80°, Rotation: 180°
Day & Night
IR cut filter with auto switch
Horizontal Resolution
700 TVL
Synchronization
Internal synchronization
S/N Ratio
More than 62 dB
Menu
Auto Gain
Low/Middle/High/Off
D/N Mode
Auto / Color / B/W / SMART
White Balance
Auto 1/Auto 2
D-WDR
Low/Middle/High/Off
Motion Detection
On/Off, maximum 6 zones
Language
English/Chinese
Function
Brightness, Contrast, Saturation, Sharpness, NR, Mirror
Interface
Video Output
1 Vp-p composite output (75 Ω, BNC connector)
Audio In
Built-in Microphone
Audio Output
1-ch audio interface (BNC connector)
General
Working Temperature
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity
90% or less (non-condensing)
Power Supply
12 VDC
Power Consumption
Max. 2W (Max. 4W with IR cut filter on)
Impact Protection
IEC 60068-2-75 test, Eh, 50J; EN 50102, up to IK07
Ingress Protection
IP66
IR Range
Up to 65 ft approx.
Dimensions
3.82" × 1.83" × 3.92" (97 × 46.6 × 99.5 mm)
Weight
0.66 lb (300 g)
© 2014 Observint Technologies. All rights reserved.