KitchenAid 8053714 Installationsanleitung Handbuch - Seite 3

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Ranges KitchenAid 8053714 herunter. KitchenAid 8053714 7 Seiten. 30" electric freestanding range

Seite drucken

Electrical Shock Hazard

Electrically ground range.

Failure to follow this instruction

could result in

death, fire or electrical shock.

If codes permit and a separate ground wire is used,

it is recommended that a qualified electrician

determine that the ground path and wire gauge are

in accordance with local codes.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not

sure range is properly grounded.

Do Not have a fuse in the neutral or ground circuit.

Recommended ground method

It is the personal responsibility

and obligation of the

customer to contact a qualified electrician to assure

that the electrical installation

is adequate and is in

conformance with the National Electrical Code,

ANSI/NFPA 70 - latest edition* and all local codes

and ordinances.

Copies of the standards listed above may be

obtained from:

Local codes may permit the use of a U.L.-listed,

250-volt, 40-ampere range power supply cord

(pigtail). This cord contains three, No.-10 copper

wires and matches a three-wire receptacle of NEMA

Type lo-50R, shown in Figure 1. Connectors on the

appliance end must be provided at the point the

power supply cord enters the appliance.

The range can be connected directly to the

fused disconnect (or circuit breaker box) through

flexible, armored or non-metallic sheathed, copper

cable (with grounding wire). Allow two to three feet

of slack in the line so that it can be moved if

servicing is ever necessary.

A U.L.-listed conduit connector must be provided at

each end of the power supply cable (at the range

and at the junction box).

* National Fire Protection Association

Wire sizes (COPPER WIRE ONLY) and connections

Batterymarch Park

must conform with the rating of the range

Quincy, Massachusetts 02269

(40-amperes).

Power supply cord is not supplied, but is available

through your local electrical supply house.

Range must be connected to the proper electrical

voltage and frequency as specified on the

model/serial rating plate. (The model/serial rating

plate is located on the oven frame behind the

storage drawer panel.)

CONNECT WITH COPPER WIRE ONLY.

Q A three-wire or four-wire, single-phase, 120/240-

volt, 60-Hz, AC-only, electrical supply (or three-wire

or four-wire 120/208-volt if specified on the

model/serial rating plate) is required on a separate,

40-ampere circuit, fused on both sides of the line.

A time-delay fuse or circuit breaker is

recommended.

i7J The wiring diagram is located on the back of

the range or on the inside of the storage drawer in a

clear plastic bag.

If connecting to a four-wire system:

This range is manufactured with the ground

connected to the cabinet. The ground must be

revised so the green grounding wire of the four-

wire power supply cord is connected to the cabinet.

See "Four-wire electrical connection,"

section,

Page 4.

When a four-wire receptacle of NEMA Type 14-50R

is used (see Figure 2), a matching U.L.-listed, four-

wire, 250-volt, 40-ampere, range power supply cord

(pigtail) must be used. This cord contains four

copper conductors with ring terminals at the

appliance end, terminating

in a NEMA Type 14-50P

plug on the supply end. The fourth (grounding)

conductor must be identified by a green or

green/yellow cover and the neutral conductor by a

white cover. Cord should be Type SRD or SRDT

with a U.L.-listed strain relief and be at least four

feet long.

The MINIMUM conductor sizes for the copper

four-wire power cord are:

40-ampere circuit

2, No.-8 conductors

1, No.-10 white neutral

1, No.-8 green grounding

3-wire wall

receptacle (lo-50R)

Figure 1

4-wire wall

receptacle (14-50Rl

Figure 2

front leveling leg

Excessive Weight Hazard

Use two or more people to move and

install range.

Failure to do so can result in back or

other injury.

Put on safety glasses and gloves. Remove

oven racks and parts package from inside oven.

Remove shipping materials, tape and protective

film from range.

cardboard

shipping b

I Do Not remove the cardboard shipping

base at this time.

Remove storage drawer. Use a 318"

ratchet to lower rear leveling legs one-half

turn. Use channel lock pliers to lower front

leveling legs one-half turn.

Contact a qualified floor covering installer for the

best procedure for drilling mounting holes through

your type floor covering.

Anti-tip bracket must be anchored securely to the

sub-floor.

Depending on the thickness of your flooring,

longer screws may be necessary to anchor the

bracket to the sub-floor. Longer screws are

available from your local hardware store.

Check that range is on cardboard shipping base

to protect floor covering.

Tip Over Hazard

A child or adult can tip the range and be

killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is

moved.

Failure to follow these instructions

can result

in death or serious burns to children and

adults.

Use the anti-tip bracket template/ instruction

sheet to install the anti-tip bracket.

age 3