KitchenAid 8053714 Installationsanleitung Handbuch - Seite 4

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Ranges KitchenAid 8053714 herunter. KitchenAid 8053714 7 Seiten. 30" electric freestanding range

Seite drucken

Electrical connection

GROUNDING INSTRUCTIONS: This range must

be grounded. In the event of malfunction

breakdown, grounding will reduce the risk of

electric shock by providing a path of least

resistance for electric current.

If using a power supply cord, the plug must be

plugged into an appropriate outlet that is

properly installed and grounded in accordance

with all local codes and ordinances.

If using a direct wire connection, this range must

be connected to a grounded metal, permanent

wiring system; or an equipment-ground

conductor must be run with the circuit

conductors and connected to the equipment-

ground terminal or lead on the range.

Pull cover down and

towards you to

remove.

l-l

block cover

3/8"

brass nuts

located inside

cover

hex-head

screws

H Remove the terminal block cover screws

located on the back of range. Pull cover down and

towards you to remove cover from range.

Depending on your electrical supply, make

the three-wire or four-wire connection following

the "Power supply cord method" or "Direct wire

method" instructions.

Electrical Shock Hazard

Turn power supply off before connecting cord.

Use a new 40-ampere power supply cord.

Plug into a grounded outlet.

Failure to follow these instructions

can result

in death, fire, or electrical shock.

WARNING - Improper connection of the equipment-

grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or

serviceman if you are in doubt as to whether the

appliance is properly grounded. Do not modify the

power supply cord plug. If it will not fit the outlet,

have a proper outlet installed by a qualified

electrician.

This range is manufactured with the neutral

terminal connected to the cabinet. Use a three-wire,

U.L.-listed, 40-ampere power supply cord (pigtail);

or if local codes Do Not permit ground through the

neutral, use a four-wire power supply cord rated at

250 volts, 40-amperes and investigated for use with

ranges. (See "Four-wire electrical connection.")

remove knockout

iFri&.9+connector

1. Disconnect the power supply.

2. Remove the knockout for the 40-ampere power

supply cord.

3. Assemble a U.L.-listed strain relief in the opening.

4. Insert the power supply cord through the strain

relief, allowing enough slack to easily attach the

wiring to the terminal block.

5. Use only ring-type terminals to connect the

power supply. To secure the power supply cord,

use the 3/8" brass terminal nuts attached to the

inside of the terminal block cover. Be sure nuts

are installed tight.

6. Complete electrical connection according to your

type electrical supply ("Three-wire electrical

connection"

or "Four-wire electrical connection.")

Three-wire electrical connection:

zl--H-ll

,ground

link

-line

GE-

neutral

(center wire)

U.L.-listed strain relief

-ampere range

power supply cord

Figure 3

Use this method ONLY if local codes PERMIT

connecting cabinet-ground

conductor to neutral

wire of power supply cord.

7. Use the brass terminal nuts attached to the

inside of the terminal block cover to connect

the neutral wire (center wire) to the silver-

colored terminal screw on the terminal block.

See Figure 3.

8. Connect the other two wires to outer

terminal screws on the terminal block. See

Figure 3.

9. Do Not loosen factory-installed

nuts already

on the terminal. Tighten nuts with 3/8" nut

driver for proper electrical connection.

10. Tighten the strain relief screws.

11. Replace the terminal block cover.

12. Plug power supply cord into grounded

electrical outlet.

Four-wire electrical connection:

Figure 4

ground-link

-screw

ground

silver-colored

terminal

block screw

U.L. listed strain

relief and 4Campere

ro;ie

power supply

Figure 5

Use this method for mobile homes and whenever

four-wire installation

is required.

7. Remove the ground-link screw from the

range frame. Save the ground-link screw.

Bend up the ground link so that it does not

contact the range. See Figure 4.

8. Connect the green ground wire from power

supply cord to the range using the ground-

link screw. The ground wire must be

attached first and must not contact any other

terminal. See Figure 5.

9. Connect the neutral wire (center wire) to the

center, silver-colored terminal screw on the

terminal block using the brass terminal nuts

that are attached to the inside of the terminal

block cover. See Figure 5.

10. Connect the other two wires to the outer

terminals on the terminal block. See Figure 5.

1 I. Do Not loosen the factory-installed

nuts

already on the terminal. Tighten nuts with 3/8'

nut driver for proper electrical connection.

12. Tighten the strain relief screws.

13. Replace the terminal block cover.

14. Plug power supply cord into grounded

electrical outlet.

Page 4