KitchenAid 9752043 Einbauanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Einbauanleitung für Ranges KitchenAid 9752043 herunter. KitchenAid 9752043 5 Seiten. 30" (76.2 cm) electric range with self-cleaning thermal/convection oven

Seite drucken

Tools needed for

installation:

level

Phillips

flat-blade

screwdriver

screwdriver or

5/16" nut

driver

pliers

safety

glasses

wrench

hand or electric drill

wood floor: 1/8" drill bit

gloves

concrete/ceramic floor:

3/16" carbide-tipped

masonry drill bit

Parts supplied for

installation:

anti-tip

bracket

2 plastic

anchors

2 screws

(#10 x 1-1/2")

Electrical

requirements

WARNING

Electrical Shock Hazard

Electrically ground range.

Failure to follow these instructions can

result in death, fire, or electrical shock.

If codes permit and a separate ground wire is

used, it is recommended that a qualified

electrician determine that the ground path is

adequate.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not

sure range is grounded.

Do Not have a fuse in the neutral or

ground circuit.

When a four-wire or three-wire, single-

phase, 120/240-volt, 60-Hz, AC-only,

electrical supply is available, a 50-ampere

maximum circuit protection is required, (or, if

specified on the model/serial rating plate, when a

four-wire or three-wire, single-phase 120/208-volt,

60 Hz, AC-only electrical supply is available, a 40-

ampere maximum circuit protection is required),

fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. The model/serial

rating plate is located on the oven frame behind the

drawer.

THE RANGE MUST BE CONNECTED

WITH COPPER WIRE ONLY.

Wire sizes and connections must conform

to the requirements of the National

Electrical Code, ANSI/NFPA 70 — latest

edition* or CSA Standard C22.1, Canadian

Electrical Code, Part 1 — latest edition** and all

local codes and ordinances for the kilowatt rating of

the range.

Copies of the standards listed may be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

Canadian Standard Association

178 Rexdale Boulevard

Rexdale (Toronto), Ontario M9W 1R3

Panel B

non-metallic sheathed, copper cable (with

ground wire). Locate the junction box to allow

two to three feet of slack in the line so that the

range can be moved if servicing is ever

necessary. Do Not cut the conduit.

3/8"

ratchet

A U.L.-listed conduit connector must be provided

at each end of the power supply cable (at the

range and at the junction box). Wires sizes

(COPPER WIRE ONLY) and connections must

conform with the rating of the range.

Electrical

connection

hammer

measuring tape

or ruler

Turn power supply off before connecting

wires.

Use 8-gauge solid copper wire.

Electrically ground range.

Failure to follow these instructions can

result in death, fire, or electrical shock.

(Bracket must be

securely mounted to

sub-floor. Thickness

This range must be connected to a grounded,

of flooring may

metallic, permanent wiring system, or a

require longer

ground connector should be connected to

screws to anchor the

the ground terminal or wire lead on the

bracket to sub-floor.)

range.

This range is manufactured with white (neutral)

power supply wire and a cabinet-connected

green ground wire twisted together.

Connect the range cable to the junction box

through a U.L.-listed conduit connector.

Complete electrical connection according to local

codes and ordinances.

Note: The metal chassis of the range MUST be

grounded in order for the control panel to work. If

the metal chassis of the range is not grounded, NO

keypads will operate. Check with a qualified

electrician if you are in doubt as to whether the

metal chassis of range is grounded.

A. If connecting to a four-wire

electrical system...

Do Not connect the cabinet-grounding

conductor to the neutral (white) junction box

wire:

Figure 1

1. Disconnect the power supply.

2. Separate the green (or bare) and white

appliance cable wires.

3. Connect the white appliance cable wire to the

neutral (white) wire in the junction box.

4. Connect the two black wires together; then the

two red wires together. See Figure 1.

5. Connect the green appliance cablewire to the

green ground wire in the junction box.

This range should be connected

directly to the fused disconnect or circuit

breaker box through flexible, armored or

WARNING

Electrical Shock Hazard

cable from

junction

power supply

box

white

wires

red

wires

black

bare or

wires

green

wires

U.L.-listed

cable from

conduit

connector

range

B. Where local codes permit...

connecting the cabinet-grounding conductor

to the neutral (white) junction box wire:

cable from

power supply

junction

box

red

wires

white

wires

bare or

green wire

cable from

Figure 2

range

Grounded Neutral

1. Disconnect the power supply.

2. Remove the terminal block cover.

3.Connect together 3 wires: green and white

appliance cable wires and the neutral (white)

wire in junction box.

4. Connect the two black wires together; then the

two red wires together. See Figure 2.

C. Where local codes DO NOT

permit...

connecting the cabinet-grounding conductor

to the neutral (white) junction box wire.

Cable from

Junction

power supply

box

Red

wires

Bare or

green

U.L.-listed

wires

conduit

cable from

Figure 3

connector

range

Grounded Neutral

1. Disconnect the power supply.

2. Separate the green and white appliance cable

wires.

3. Connect the white appliance cable wire to the

neutral (white) wire in the junction box.

4. Connect the two black wires together; then the

two red wires together. See Figure 3.

5. Connect the green or bare ground wire from

the appliance cable to a grounded wire in the

junction box.

Now start...

With range in kitchen.

Put on safety glasses and gloves.

Remove shipping materials, tape and

protective film from range. Keep

cardboard bottom and shipping base under

range. Remove oven racks and parts package

from inside oven.

Take 4 cardboard

corners from the

carton. Stack one

cardboard corner

on top of another.

Repeat with the

other two

corners. Place

spacers

corners lengthwise

on the floor in back of range so corners will

support outer side edges of range as shown.

black

wires

U.L.-listed

conduit

connector

White

wires

Black wires

cardboard

corners