AVWARE AVW517 Schnellstart-Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Digitalkamera AVWARE AVW517 herunter. AVWARE AVW517 2 Seiten.

Seite drucken

WDR ON

WHI T E BA L A NCE ( Whit e Bal.)

1. When SET U P menu scr een i s di spl ay ed, sel ect 'Whi t e Bal .' by usi ng U p and

Dow n but t ons so t hat t he ar r ow i ndi cat es Whi t e Bal .

※ Sel ect one of t he f ol l ow i ng 6 modes, as appr opr i at e f or y our pur pose

▶ A WB : Select this when the color temperature is between 2,000ºK and 18,000ºK.

▶ A WC- > SET : To find the optimal setting for the current luminance environment in this

mode, set the point the camera towards a sheet of white paper and press

the SET button. If the environment changes, readjust it.

▶ M A N U A L : Select this to fine-tune White Balance manually. Set White Balance first by using

the ATW or AWC mode. After that switch to MANUAL mode.

Adjust the [BLUE] and [RED], according to the changing of color on the screen

▶ I N DOOR : Select this when the color temperature is around 3,100ºK.

▶ OU T DOOR : Select this when the color temperature is around 5,100ºK.

▶ A T W : Select this when the color temperature is between 2,500ºK and 9,800ºK.

⊙ White balance may not work properly under the following conditions.

Notes

In this case, select the AWC mode.

① When color temperature of environment surrounding the subject is out of the control range

② If the camera towards a fluorescent, the White Balance operation may become unstable

DA Y/ NI GHT

● You can di spl ay pi ct ur es i n Col or or Bl ack and Whi t e.

1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'DA Y/ N I GH T ' by usi ng t he U p

and Dow n but t ons so t hat t he ar r ow i ndi cat es 'DA Y/ N I GH T '

▶ COL OR : The picture is always displayed in color.

▶ A U T O : The mode is switched to color in a normal environment, but switches to B/W mode

when ambient illumination is low. To set up the switching time or speed

for auto mode, press the SET button

- Delay : You can select the duration time about changing the day/night mode.

- S / E - Level : You can select brightness of illumination about changing the day/night mode.

-> The brightness of illumination is changeable by installed environment.

▶ EXT : Deactivates the EXT function.

▶ BW : The picture is always displayed in B/W.

Notes

⊙ You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is 'OFF'

At this time, the exchange between DAY mode and NIGHT mode operates as COLOR mode

* Mirror

- Mirror : you can flip the image vertically on the screen.

- Rotate : you can flip the imate horizontally on the screen.

- V-Flip : you can flip the image vertically and horizontally both.

* Digital Zoom : You can use a digital zoom of x1.0 ~ X32

* Gamma : Standard value is 0.45. You can adjust the value between 0.05 ~ 1.00

* NEG IMAGE : you can flip the color on screen.

▶ RS 485 : Deactivates the RS485 function.

▶ M OT I ON : If you connect an alarm device to this camera, you can monitor activity

because a signal is generated by the camera whenever motion is detected. The

motion detection signal is output through the MD OUT port.

① When the SPECIAL menu is displayed, press the

Up and Down buttons so that arrow indicates

MOTION.

② Press SET button for sub menu.

③ Set up the mode using 4 direction buttons.

* AREA SELECT : Determines which 4 vertices of

each MD area is to be used

* AREA DIPLAY : Determines whetehr to use the MD area selected in Sensitivity.

* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.

* WIDTH : Adjust the selected vertical area.

* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.

* HEIGHT : Adjust the selected horizontal area.

* Sensitivity : You can select up to 4 areas. When sensitivity number is high,

motion detection sensitivity is increased to recognize even small movement

* Motion View : If you make it ON by using LEFT and RIGHT buttons, selected

value of color is filled on the screen

Notes

⊙ MD areas show only MOTION menu. Therefore, MD areas don't display on the monitor screen.

⊙ BUT if you select the motion view function ON, MD areas are displayed on the monitor

WDR OFF

3 Digit al Noise Reduct ion( 3DNR)

● T hi s f unct i on r educes t he back gr ound noi se i n a l ow l umi nance env i r onment

1. When t he SET U P menu scr een i s di spl ay ed, sel ect 3DN R by usi ng t he U p and

Dow n but t ons so t hat t he ar r ow i ndi cat es 3DN R.

2. Sel ect a desi r ed mode usi ng t he L ef t and Ri ght but t ons.

▶ OFF : Deactivates 3DNR. Noise is not reduced.

▶ ON : Activates 3DN so that noise is reduced.

3. Set t he 3DN R mode t o 'ON ' andpr ess t he SET but t on. T hen y ou can adj ust t he

N oi se r educt i on l ev el .

Notes

⊙ You cannot set the 3DNR to 'ON' or 'OFF' when the AGC mode of the EXPOSURE menu is

⊙ When adjusting the noise reduction level of the 3DNR mdoe, the higher the level set ,

'OFF'.

the more the noise level will be reduced but that after image may also occur.

SPECI A L

1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'SPECI A L ' by usi ng U p and

Dow n but t ons so t hat t he ar r ow i ndi cat es 'SPECI A L '

2. Sel ect a desi r ed mode usi ng t he U p and Dow n but t ons

▶ CA M T I T L E : If you enter a title, the title will be appear on the monitor.

① If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow

indicates 'CAM TITLE'

② Set it to 'On' by using Left and Right buttons.

⊙ When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if

Notes

you

③ Press the SET button.

④ Use the 4 direction buttons to move to a desired letter and select the letter by pressing the

SET button. Repeat this to enter multiple letters. You can enter up 15 letters.

⊙ If you entered wrong letter......

Notes

If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a

leeter,

change the cursor to the bottom left arrow and press the SET button. Move the curson over the

⑤ Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears

on the screen. Select the position to display the title on the screen by using the 4 directoin

buttons and press the SET button. When the position is determined, select 'END' and press

the SET button to return to the SPECIAL menu.

▶ D- EFFECT

① When the SPECIAL menu screen is displayed, press the Up and down buttons so that the

arrow indicates "D-EFFECT".

② Press the SET button for Sub menu.

* Freeze : You can stop the image or reactivate it.

▶ PRI V A CY : Hide an area you want to hide on the screen.

① When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the

arrow indecates 'PRIVACY'.

② Press SET button for Sub Menu.

③ Set up the mode by using 4 direction buttons.

* AREA SELECT : You can select up to 8 privacy areas.

* AREA DISPLAY : Determines whether to use the area selected in the AREA SELECT.

* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.

* WIDTH : adjust the selected vertical area.

* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.

* HEIGHT : adjust the selected horizontal area.

* COLOR : Determine area color. You can select 0 ~ 15.

▶ L anguage : You can select the menu language according to your requirement.

- It can be changes 5sec. later.

- Supplied Language : English, Chinese, Japanese

A DJUST

1. When t he SET U P menu scr een i s di spl ay ed, sel ect A DJU ST by usi ng U p and

Dow n but t ons so t hat ar r ow i ndi cat es A DJU ST .

▶ Shar pness : As you increase this value, the picture outline becomes stronger and clearer

Adjust this value appropriately depending on the sharpness of the picture.

▶ BL U E : You can adjust the color on the monitor in BLUE mode by controlling between

0 and 100

▶ RED : You can adjust the color on the monitor in RED mode by controlling between

0 and 100

RESET

1. When t he SET U P menu scr een i s di spl ay ed, sel ect RESET by usi ng U p and

Dow n but t ons so t hat ar r ow i ndi cat es RESET .

2. Sel ect a mode by usi ng U p and Dow n but t ons.

▶ FA CT ORY : Resets the camera settings to the factory defaults.

Language and Communication status is not initialized

EXI T

Press the SET button in the Exit menu to save the current settings and exit the Main SETUP

menu.