AVWARE AVW517 Manuel de démarrage rapide - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} AVWARE AVW517. AVWARE AVW517 2 pages.
Imprimer la page
WDR ON
WHI T E BA L A NCE ( Whit e Bal.)
1. When SET U P menu scr een i s di spl ay ed, sel ect 'Whi t e Bal .' by usi ng U p and
Dow n but t ons so t hat t he ar r ow i ndi cat es Whi t e Bal .
※ Sel ect one of t he f ol l ow i ng 6 modes, as appr opr i at e f or y our pur pose
▶ A WB : Select this when the color temperature is between 2,000ºK and 18,000ºK.
▶ A WC- > SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the SET button. If the environment changes, readjust it.
▶ M A N U A L : Select this to fine-tune White Balance manually. Set White Balance first by using
the ATW or AWC mode. After that switch to MANUAL mode.
Adjust the [BLUE] and [RED], according to the changing of color on the screen
▶ I N DOOR : Select this when the color temperature is around 3,100ºK.
▶ OU T DOOR : Select this when the color temperature is around 5,100ºK.
▶ A T W : Select this when the color temperature is between 2,500ºK and 9,800ºK.
⊙ White balance may not work properly under the following conditions.
Notes
In this case, select the AWC mode.
① When color temperature of environment surrounding the subject is out of the control range
② If the camera towards a fluorescent, the White Balance operation may become unstable
DA Y/ NI GHT
● You can di spl ay pi ct ur es i n Col or or Bl ack and Whi t e.
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'DA Y/ N I GH T ' by usi ng t he U p
and Dow n but t ons so t hat t he ar r ow i ndi cat es 'DA Y/ N I GH T '
▶ COL OR : The picture is always displayed in color.
▶ A U T O : The mode is switched to color in a normal environment, but switches to B/W mode
when ambient illumination is low. To set up the switching time or speed
for auto mode, press the SET button
- Delay : You can select the duration time about changing the day/night mode.
- S / E - Level : You can select brightness of illumination about changing the day/night mode.
-> The brightness of illumination is changeable by installed environment.
▶ EXT : Deactivates the EXT function.
▶ BW : The picture is always displayed in B/W.
Notes
⊙ You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is 'OFF'
At this time, the exchange between DAY mode and NIGHT mode operates as COLOR mode
* Mirror
- Mirror : you can flip the image vertically on the screen.
- Rotate : you can flip the imate horizontally on the screen.
- V-Flip : you can flip the image vertically and horizontally both.
* Digital Zoom : You can use a digital zoom of x1.0 ~ X32
* Gamma : Standard value is 0.45. You can adjust the value between 0.05 ~ 1.00
* NEG IMAGE : you can flip the color on screen.
▶ RS 485 : Deactivates the RS485 function.
▶ M OT I ON : If you connect an alarm device to this camera, you can monitor activity
because a signal is generated by the camera whenever motion is detected. The
motion detection signal is output through the MD OUT port.
① When the SPECIAL menu is displayed, press the
Up and Down buttons so that arrow indicates
MOTION.
② Press SET button for sub menu.
③ Set up the mode using 4 direction buttons.
* AREA SELECT : Determines which 4 vertices of
each MD area is to be used
* AREA DIPLAY : Determines whetehr to use the MD area selected in Sensitivity.
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
* WIDTH : Adjust the selected vertical area.
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
* HEIGHT : Adjust the selected horizontal area.
* Sensitivity : You can select up to 4 areas. When sensitivity number is high,
motion detection sensitivity is increased to recognize even small movement
* Motion View : If you make it ON by using LEFT and RIGHT buttons, selected
value of color is filled on the screen
Notes
⊙ MD areas show only MOTION menu. Therefore, MD areas don't display on the monitor screen.
⊙ BUT if you select the motion view function ON, MD areas are displayed on the monitor
5
WDR OFF
7
3 Digit al Noise Reduct ion( 3DNR)
● T hi s f unct i on r educes t he back gr ound noi se i n a l ow l umi nance env i r onment
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 3DN R by usi ng t he U p and
Dow n but t ons so t hat t he ar r ow i ndi cat es 3DN R.
2. Sel ect a desi r ed mode usi ng t he L ef t and Ri ght but t ons.
▶ OFF : Deactivates 3DNR. Noise is not reduced.
▶ ON : Activates 3DN so that noise is reduced.
3. Set t he 3DN R mode t o 'ON ' andpr ess t he SET but t on. T hen y ou can adj ust t he
N oi se r educt i on l ev el .
Notes
⊙ You cannot set the 3DNR to 'ON' or 'OFF' when the AGC mode of the EXPOSURE menu is
⊙ When adjusting the noise reduction level of the 3DNR mdoe, the higher the level set ,
'OFF'.
the more the noise level will be reduced but that after image may also occur.
SPECI A L
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'SPECI A L ' by usi ng U p and
Dow n but t ons so t hat t he ar r ow i ndi cat es 'SPECI A L '
2. Sel ect a desi r ed mode usi ng t he U p and Dow n but t ons
▶ CA M T I T L E : If you enter a title, the title will be appear on the monitor.
① If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow
indicates 'CAM TITLE'
② Set it to 'On' by using Left and Right buttons.
⊙ When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if
Notes
you
③ Press the SET button.
④ Use the 4 direction buttons to move to a desired letter and select the letter by pressing the
SET button. Repeat this to enter multiple letters. You can enter up 15 letters.
⊙ If you entered wrong letter......
Notes
If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a
leeter,
change the cursor to the bottom left arrow and press the SET button. Move the curson over the
⑤ Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears
on the screen. Select the position to display the title on the screen by using the 4 directoin
buttons and press the SET button. When the position is determined, select 'END' and press
the SET button to return to the SPECIAL menu.
▶ D- EFFECT
① When the SPECIAL menu screen is displayed, press the Up and down buttons so that the
arrow indicates "D-EFFECT".
② Press the SET button for Sub menu.
* Freeze : You can stop the image or reactivate it.
▶ PRI V A CY : Hide an area you want to hide on the screen.
① When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the
arrow indecates 'PRIVACY'.
② Press SET button for Sub Menu.
③ Set up the mode by using 4 direction buttons.
* AREA SELECT : You can select up to 8 privacy areas.
* AREA DISPLAY : Determines whether to use the area selected in the AREA SELECT.
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
* WIDTH : adjust the selected vertical area.
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
* HEIGHT : adjust the selected horizontal area.
* COLOR : Determine area color. You can select 0 ~ 15.
▶ L anguage : You can select the menu language according to your requirement.
- It can be changes 5sec. later.
- Supplied Language : English, Chinese, Japanese
A DJUST
1. When t he SET U P menu scr een i s di spl ay ed, sel ect A DJU ST by usi ng U p and
Dow n but t ons so t hat ar r ow i ndi cat es A DJU ST .
▶ Shar pness : As you increase this value, the picture outline becomes stronger and clearer
Adjust this value appropriately depending on the sharpness of the picture.
▶ BL U E : You can adjust the color on the monitor in BLUE mode by controlling between
0 and 100
▶ RED : You can adjust the color on the monitor in RED mode by controlling between
0 and 100
RESET
1. When t he SET U P menu scr een i s di spl ay ed, sel ect RESET by usi ng U p and
Dow n but t ons so t hat ar r ow i ndi cat es RESET .
2. Sel ect a mode by usi ng U p and Dow n but t ons.
▶ FA CT ORY : Resets the camera settings to the factory defaults.
Language and Communication status is not initialized
EXI T
Press the SET button in the Exit menu to save the current settings and exit the Main SETUP
menu.
copyright www.avware.de
6
8