Dialight Reliant Betriebs- und Installationsanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Betriebs- und Installationsanleitung für DJ-Ausrüstung Dialight Reliant herunter. Dialight Reliant 14 Seiten. High bay

Seite drucken

WARNING:

To avoid the risk of fire, explosion, or electric

shock, this product should be installed,

inspected, and maintained by a qualified

electrician

accordance

applicable electrical rules and regulations.

Safety Instruction:

To avoid electric shock:



Be certain electrical power is OFF

before and during installation and

maintenance.



Luminaire must be connected to a

wiring system with an equipment-

grounding conductor.



Make sure the supply voltage is the

same as the rated luminaire voltage.



The technical data indicated on the

LED luminaires are to be observed.



Changes of the design and

modifications to the LED luminaire are

not permitted.



Observe the national/regional

electrical safety rules and regulations

during installation.



The LEDs of this luminaire are not

replaceable; when the LEDs reach

their end of life, the whole luminaire

shall be replaced.



Before the unit goes into service,

ensure 4x lens frame safety screws

(8-32 socket head cap screws and

lock washers) have been factory

installed. If reinstalling the frame,

Loctite 425 should be used.

Equipment Application

This product can be used indoors only to

illuminate areas of a light industrial location.

General Mounting Information

The luminaire may be mounted using the

externally visible tabs and appropriately sized

cable or chain.

Dialight sold mounting accessories are available

and should be installed according to the

instructions provided with the accessory.

WARNING:

Please

ensure

structure can handle the weight of the luminaire.

Dialight is not responsible for any damages to

the application structure or the luminaire when

mounted improperly.

Installation

Ensure that the mains voltage supply is

disconnected before connecting the luminaire.

Install the equipment in accordance with the

manufacturer's instructions as well as any other

applicable electric codes.

Always transport and store the equipment in its

original packaging and keep in a dry location.

When unpacking, check for any cracks or

damage in the housing or lens. If in doubt, do not

install.

Page

Reliant High Bay Americas – UL1598

Technical Data:

Locations:

Temperature Range:

with

all

RHU**********(N)

RHU**********(F/G)

Rated Input Voltage:

RHU***(2/8)*******

RHU***(5/9)*(D/E/G/J/K)****(N)

Power Consumption:

RH****(2/8)C******

RH****(2/8)E******

RH****(2/8)F******

RH****(2/8)H******

RH****(2/8)L******

RH****(2/8)N******

RH****(2/8)R******

RH****(5/9)C******

RH****(5/9)E******

RH****(5/9)F******

RH****(5/9)H******

RH****(5/9)L******

RH****(5/9)N******

RH****(5/9)R******

*NOTE: ON MODELS EQUIPPED WITH BATTERY

BACKUP, UNIT MAY CONSUME UP TO AN

ADDITIONAL 6W DURING CHARGING.

*NOTE: ON MODELS EQUIPPED WITH

UPLIGHTING, UNIT MAY CONSUME UP TO AN

ADDITIONAL 10% OF WATTAGE.

Weight:

RH*****(C/E/F/H)******

RH*****(L/N/R)******

Dimensions:

NOTE: The cabling used must be suitable for the

site application and/or the site requirements.

When assembling the cable entries for the mains

connection, always observe the manufacturer's

the

application

specifications for the glands used.

NOTE: The addition of cable glands, dust caps,

electrical plugs, or occupancy sensors may

change the IP rating of this luminaire.

WARNING: Do not over tighten as the protection

rating may be compromised. Always refer to the

gland manufacturer's data for torque settings.

Opening/Closing the Luminaire:

To open the luminaire, the access cover captive

screw must be loosened. If the luminaire is

equipped with an occupancy sensor, rotate the

lens ¼ turn counterclockwise and remove. The

two snap feature tabs may then be depressed

to allow the access cover to swing open.

Suitable for Damp Locations

-40⁰F to +131⁰F

[-40⁰C to +55⁰C]

+50⁰F to +95⁰F

[+10⁰C to +35⁰C]

100-277 VAC

50/60Hz

347-480 VAC

50/60Hz

123 W

163 W

199 W

239 W

325 W

398 W

478 W

125 W

166 W

203 W

244 W

331 W

406 W

487 W

18-25 lbs.

[8.2-11.3 kg]

41-56 lbs.

[18.6-25.4kg]

See Technical Diagrams

Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727

Tel: 732 919 3119

To close the luminaire, ensure there are no wires

or other obstructions that will prevent the access

cover to close. Swing the cover closed and

ensure the two snap features have engaged. If

the luminaire is equipped with an occupancy

sensor, re-install the lens by sliding it onto the

sensor and then twisting ¼ turn clockwise until

snug. Then tighten the captive screw on the

access cover. Torque to 14-16 in-lbs.

Electrical Connections

The luminaire may be supplied from the factory

with a three core colored cable.

If no cable is factory installed, the unit will be

supplied with a customer interface harness that

has six-inch flying leads. Connect directly to the

interface harness using an appropriate wire

connector (Lever nut, wire nut, etc.). The supply

cable must be at least 18 AWG and rated to

90⁰C minimum. A suitably sized ½" or ¾" NPT

cable gland must also be used.

100-277 VAC SINGLE PHASE – NORTH

AMERICA

SYMBOL

COLOR

GREEN

WHITE

BLACK

DIM +

VIOLET

DIM -

GREY

347 VAC SINGLE PHASE – NORTH AMERICA

SYMBOL

COLOR

GREEN

RED

BLACK

DIM +

VIOLET

DIM -

GREY

9100RHB005000 REV C

Fax: 732 751 5778

www.dialight.com

CONNECTION

EARTH

NEUTRAL

LIVE

DIMMING

CONNECTION

EARTH

NEUTRAL

LIVE

DIMMING