- ページ 3
DJ機材 Dialight ReliantのPDF 操作およびインストール手順をオンラインで閲覧またはダウンロードできます。Dialight Reliant 14 ページ。 High bay
ページを印刷するWARNING:
To avoid the risk of fire, explosion, or electric
shock, this product should be installed,
inspected, and maintained by a qualified
electrician
in
accordance
applicable electrical rules and regulations.
Safety Instruction:
To avoid electric shock:
Be certain electrical power is OFF
before and during installation and
maintenance.
Luminaire must be connected to a
wiring system with an equipment-
grounding conductor.
Make sure the supply voltage is the
same as the rated luminaire voltage.
The technical data indicated on the
LED luminaires are to be observed.
Changes of the design and
modifications to the LED luminaire are
not permitted.
Observe the national/regional
electrical safety rules and regulations
during installation.
The LEDs of this luminaire are not
replaceable; when the LEDs reach
their end of life, the whole luminaire
shall be replaced.
Before the unit goes into service,
ensure 4x lens frame safety screws
(8-32 socket head cap screws and
lock washers) have been factory
installed. If reinstalling the frame,
Loctite 425 should be used.
Equipment Application
This product can be used indoors only to
illuminate areas of a light industrial location.
General Mounting Information
The luminaire may be mounted using the
externally visible tabs and appropriately sized
cable or chain.
Dialight sold mounting accessories are available
and should be installed according to the
instructions provided with the accessory.
WARNING:
Please
ensure
structure can handle the weight of the luminaire.
Dialight is not responsible for any damages to
the application structure or the luminaire when
mounted improperly.
Installation
Ensure that the mains voltage supply is
disconnected before connecting the luminaire.
Install the equipment in accordance with the
manufacturer's instructions as well as any other
applicable electric codes.
Always transport and store the equipment in its
original packaging and keep in a dry location.
When unpacking, check for any cracks or
damage in the housing or lens. If in doubt, do not
install.
Page
3
Reliant High Bay Americas – UL1598
Technical Data:
Locations:
Temperature Range:
with
all
RHU**********(N)
RHU**********(F/G)
Rated Input Voltage:
RHU***(2/8)*******
RHU***(5/9)*(D/E/G/J/K)****(N)
Power Consumption:
RH****(2/8)C******
RH****(2/8)E******
RH****(2/8)F******
RH****(2/8)H******
RH****(2/8)L******
RH****(2/8)N******
RH****(2/8)R******
RH****(5/9)C******
RH****(5/9)E******
RH****(5/9)F******
RH****(5/9)H******
RH****(5/9)L******
RH****(5/9)N******
RH****(5/9)R******
*NOTE: ON MODELS EQUIPPED WITH BATTERY
BACKUP, UNIT MAY CONSUME UP TO AN
ADDITIONAL 6W DURING CHARGING.
*NOTE: ON MODELS EQUIPPED WITH
UPLIGHTING, UNIT MAY CONSUME UP TO AN
ADDITIONAL 10% OF WATTAGE.
Weight:
RH*****(C/E/F/H)******
RH*****(L/N/R)******
Dimensions:
NOTE: The cabling used must be suitable for the
site application and/or the site requirements.
When assembling the cable entries for the mains
connection, always observe the manufacturer's
the
application
specifications for the glands used.
NOTE: The addition of cable glands, dust caps,
electrical plugs, or occupancy sensors may
change the IP rating of this luminaire.
WARNING: Do not over tighten as the protection
rating may be compromised. Always refer to the
gland manufacturer's data for torque settings.
Opening/Closing the Luminaire:
To open the luminaire, the access cover captive
screw must be loosened. If the luminaire is
equipped with an occupancy sensor, rotate the
lens ¼ turn counterclockwise and remove. The
two snap feature tabs may then be depressed
to allow the access cover to swing open.
Suitable for Damp Locations
-40⁰F to +131⁰F
[-40⁰C to +55⁰C]
+50⁰F to +95⁰F
[+10⁰C to +35⁰C]
100-277 VAC
50/60Hz
347-480 VAC
50/60Hz
123 W
163 W
199 W
239 W
325 W
398 W
478 W
125 W
166 W
203 W
244 W
331 W
406 W
487 W
18-25 lbs.
[8.2-11.3 kg]
41-56 lbs.
[18.6-25.4kg]
See Technical Diagrams
Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727
Tel: 732 919 3119
To close the luminaire, ensure there are no wires
or other obstructions that will prevent the access
cover to close. Swing the cover closed and
ensure the two snap features have engaged. If
the luminaire is equipped with an occupancy
sensor, re-install the lens by sliding it onto the
sensor and then twisting ¼ turn clockwise until
snug. Then tighten the captive screw on the
access cover. Torque to 14-16 in-lbs.
Electrical Connections
The luminaire may be supplied from the factory
with a three core colored cable.
If no cable is factory installed, the unit will be
supplied with a customer interface harness that
has six-inch flying leads. Connect directly to the
interface harness using an appropriate wire
connector (Lever nut, wire nut, etc.). The supply
cable must be at least 18 AWG and rated to
90⁰C minimum. A suitably sized ½" or ¾" NPT
cable gland must also be used.
100-277 VAC SINGLE PHASE – NORTH
AMERICA
SYMBOL
COLOR
GREEN
N
WHITE
L
BLACK
DIM +
VIOLET
DIM -
GREY
347 VAC SINGLE PHASE – NORTH AMERICA
SYMBOL
COLOR
GREEN
N
RED
L
BLACK
DIM +
VIOLET
DIM -
GREY
9100RHB005000 REV C
Fax: 732 751 5778
www.dialight.com
CONNECTION
EARTH
NEUTRAL
LIVE
DIMMING
DIMMING
CONNECTION
EARTH
NEUTRAL
LIVE
DIMMING
DIMMING