Dialogic D600JCT-1E1-120-EW Installationshandbuch

Blättern Sie online oder laden Sie pdf Installationshandbuch für Computer Hardware Dialogic D600JCT-1E1-120-EW herunter. Dialogic D600JCT-1E1-120-EW 2 Seiten. Combined media board

Seite drucken

Dialogic

D/600JCT-1E1-120-EW

Installation Guide

1. Product Description

The Dialogic

D/600JCT-1E1-120-EW combined

media board provides up to 30 channels of voice and

media resources and a single, 120-ohm E1 telephony

interface in a single, full-length PCI Express slot.

Additional Information

Additional information about the

D/600JCT-1E1-120-EW is available from a number of

sources.

The product data sheet, available at

http://www.dialogic.com/products/list.asp, provides

a functional description as well as information about

applications and configurations, features, and

technical specifications.

Refer to the Release Guide and the online Release

Update for your Dialogic system software release to

verify that the D/600JCT-1E1-120-EW is supported in

the release, and for information on any new features

or issues that may relate to it.

The Regulatory Notices document that is packed with

each D/600JCT-1E1-120-EW board contains safety

warnings and national requirements for proper

operation of telecommunications equipment.

2. Before You Begin

Protecting the Board from Damage

CAUTION: All computer boards are sensitive to

electrostatic discharge. Handle all static-sensitive

boards and components at a static-safe work area,

and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions,

visit http://www.dialogic.com/support/hwinstall to

learn more.

Unpacking the Board

Unpack the board according to the following steps:

1. Prepare a static-safeguarded work area.

2. Carefully remove the board from the shipping

carton and static-shielding bag. Handle the board

Part number: 64-0101-02

Physical Layout

by the edges and avoid touching the board's

components.

3. Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when

carrying boards from station to station.

CAUTION: Do not remove the board from the

anti-static packaging until you are ready to install it.

Observe proper anti-static precautions at all times.

1. Network connector: RJ48C

connector to external E1 digital

telephone network interface.

2. Alarm/status LEDs

Red LED (Loopback)—Indicates

remote loopback mode.

Green LED—Indicates board is

powered up and receiving signal

from external E1 source.

Yellow LED—Indicates loss of

frame synchronization at far end of

external network.

Red LED—Indicates loss of frame

synchronization on incoming line

from external network.

3. SW100: Rotary switch used to set

board ID number.

4. SW500: Selects loopback mode.

Loopback mode is selected when

switch slider is set to the position

farther from the bracket. Default

setting is normal mode (slider

closer to bracket).

5. SW600: Not used.

0 0

P 7

6. CT Bus connector: H.100

telephony bus connector.

7. P700: CT Bus termination jumper.

8. PCI Express connector: Host bus

connector. Compatible with x1 or

larger PCI Express Link connectors.

CT Bus

9. Power Budgeting Jumper P3:

Termination

3-pin jumper to set how the board

Pins

responds to the system power

budgeting function.

P3 jumper in pins 2-3: Board

■

adheres to power budgeting values

set by system.

P3 jumper in pins 1-2: Board

■

ignores power budgeting values

set by system.

Factory default is P3 jumper in pins

2-3.

3. Configuring the Board

The D/600JCT-1E1-120-EW board uses Plug and Play

technology to simplify installation. No user

configuration is required for IRQ or memory address.

The D/600JCT-1E1-120-EW board has three manually

configurable options:

Board ID

■

CT Bus termination

■

Remote loopback mode

■

Power budgeting (see Choosing a Slot section

■

below)

Setting the Board ID

When the system is started, each Dialogic telecom

board is assigned a board instance ID number that

programs can use to identify individual boards in a

multi-board system. The setting of SW100 controls

the generation of the instance numbers.

Windows* Systems: In a Windows system, leaving

SW100 set to the 0 position (the factory default

setting) on all Dialogic telecom boards causes the

system software to assign instance numbers

geographically, based on the bus and slot numbers.

Note that when using this method, there is no way

to know what the instance numbers will be until the

system is started and configured, and the instance

number for any given board is likely to change

when there is any change in the number or

arrangement of boards in the system.

As an alternative, you may set SW100 on each

board to a different position (0-9 or A-F) to

explicitly assign specific ID numbers to the boards.

Note that each board must be set to a different ID

number.

In either case, you can read the ID numbers

assigned to the boards in the Dialogic Configuration

Manager after you start the system and invoke that

tool.

Linux* Systems: In a Linux system, you must

explicitly specify the board ID numbers by setting

SW100 on each board to a different position (0-9

or A-F). Refer to the Configuration Guide for

Springware architecture products in your Dialogic

system software documentation for further

information about the board ID numbers.

Setting the CT Bus Termination

In some systems that connect multiple boards with a

CT Bus cable, it is desirable to terminate the bus

signal on the boards that are connected at each end

of the cable, but this is generally not necessary. If

your system requires termination and this board will

be the end-most board on the CT Bus cable, install a

jumper link (not supplied) over the bottom pair of

pins of P700 as indicated in the Physical Description

section. Use any standard 2mm pitch jumper link,

such as Methode item number 8610-202-70.

Setting the Remote Loopback Mode

The D/600JCT-1E1-120-EW board is shipped with

SW500 set for normal operation, with the switch

slider in the position closer to the board's bracket.

Setting this switch to the opposite position selects the

loopback mode and overrides any board modes set

by your application. Loopback mode is commonly

used to check the network connection after the

firmware has been downloaded to the board.

4. Choosing a Slot

The D/600JCT-1E1-120-EW board is a full length x1

form factor PCI Express board that requires 25W of

power. The following explanation and guidelines are