Dialogic D600JCT-1E1-120-EW Installationshandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Installationshandbuch für Computer Hardware Dialogic D600JCT-1E1-120-EW herunter. Dialogic D600JCT-1E1-120-EW 2 Seiten. Combined media board

Seite drucken

provided to ensure proper configuration of the

product.

Power Budgeting is a new feature, introduced in the

PCI Express Specification, that provides a mechanism

to enable a system to negotiate power consumption

requirements for add-in devices.

Per PCI Express Card Electromechanical Specification

Revision 1.0a or higher, a x1 add-in card can draw no

more than 10W in a x1 slot unless the board's

required power is successfully negotiated and

allocated by the system (power budgeting). However,

implementation of power budgeting by a vendor's

system is not a compliance requirement per the PCI

Express Card Electromechanical Specification

Revision 1.0a or higher. Therefore, some chassis may

not support this feature. Power Budgeting jumper P3

is designed to ensure proper configuration of the

product.

The D/600JCT-1E1-120-EW board must be installed

in a slot that can be allocated 25W.

If Power Budgeting is not implemented by a vendor's

system, the D/600JCT-1E1-120-EW board must be

plugged into a x4 or higher slot with the P3 jumper in

position 1-2 (power budgeting ignored). This is

allowed per PCI Express Card Electromechanical

Specification Revision 1.0a or higher because a x4 or

greater slot must be able to support a minimum of

25W.

If Power Budgeting is implemented by a vendor's

system, the D/600JCT-1E1-120-EW board can be

plugged into a x1 slot but the P3 jumper must be in

position pins 2-3 (power budgeting adhered to).

WARNING! Installing the

D/600JCT-1E1-120-EW board in a x1 slot with

the P3 jumper in position 1-2 will void the

warranty of the D/600JCT-1E1-120-EW board.

If the D/600JCT-1E1-120-EW will be connected to

other telephony boards via a CT Bus cable, you

should install the boards to minimize unused

connectors on the CT Bus cable (in addition to

ensuring that the power requirements are met):

Install boards in adjacent slots whenever possible.

■

If the D/600JCT-1E1-120-EW board will be

■

connected to one or more PCI boards, use the PCI

Express slot(s) closest to the PCI slots.

5. Installing the Board

WARNING! Unplug the equipment before

performing the procedures described here.

Failure to disconnect the power before you

open the chassis can result in personal injury.

Ensure that the system is disconnected from its

power source and from all telecommunications

links, networks, or modem lines whenever the

chassis cover is removed. Do not operate the

system with the cover removed.

CAUTION: To avoid possible damage to the board,

remove power from the computer before beginning

installation. Observe proper anti-static precautions at

all times while handling and installing the board.

To install the D/600JCT-1E1-120-EW board, perform

the following steps:

1. Turn off all power to the system and disconnect

the system's power cords.

2. Remove the computer's cover.

3. Choose an empty PCI Express expansion slot and

remove the slot's retaining screw and access

cover plate.

4. Insert the board's edge connector into the bus

slot, and apply firm pressure to the top edge of

the board until the board is fully seated in the

edge connector.

Remove

Cover

PCI Express

Plate

Board

Computer

Chassis

PCI Express

Slots

PCI Slots

5. Reinstall the retaining screw.

6. Repeat steps 1 through 5 for any additional

boards you are installing.

7. Connect the telephony boards together with a CT

Bus cable of the appropriate size (not included). If

possible, use a cable assembly that matches the

number of boards in your system. If the cable has

more than one unused connector, install the cable

so that all the unused connectors are at one end

of the cable.

8. Replace the computer's cover.

9. Reconnect the computer's power cord.

CT Bus

Colored

Cable

Stripe

(Pin 1)

Note:

Your CT Bus cable may

have a different number of

connectors (drops).

6. Connecting to External Equipment

The RJ-48C jack on the rear bracket of the

D/600JCT-1E1-120-EW board supports a single

120-ohm E1 digital network interface. Use an

appropriate cable to connect the RJ-48C jack on the

bracket to your CSU or other network termination

equipment.

The following figure illustrates the pinout of the

RJ-48C jack.

Pinout for RJ–48C Jacks

Network Interface

on PCI Express Bracket

Cable Connector

RCV_RING

Pin 1

RCV_TIP

Chassis Ground

XMIT_RING

XMIT_TIP

Chassis Ground

7. After Installing the Board

If you are installing the D/600JCT-1E1-120-EW in a

system that already has the Dialogic system software

installed, you may not need to install a new or

upgraded software release to support the board. The

D/600JCT-1E1-120-EW has been designed to be

compatible with existing System Release 6.x software

versions that support PCI boards. Please refer to the

Release Update document for your release version for

up-to-date information about support for PCI Express

boards and any known issues relating to their use.

If this is the first Dialogic telecom board you have

installed in your system, you will need to install an

appropriate version of the Dialogic system software

and configure the software for the specific board(s)

you are using. Refer to the installation and

configuration documentation that accompanies the

release for instructions.

When configuring your system for the

D/600JCT-1E1-120-EW board, use the same menu

selections and configuration settings as for the PCI

version of the D/600JCT-2E1.

8. Removing the Board

Removal of the D/600JCT-1E1-120-EW board is

essentially the reverse of the installation procedure:

1. Observe anti-static precautions.

2. Disconnect the telephony cables.

3. Remove the computer's power cord.

4. Remove the computer's cover.

5. Disconnect the CT Bus cable (if applicable).

6. Remove and set aside the board's retaining screw.

7. Remove the board and place it static-protective

packaging.

9. Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who

are trained to answer technical questions on installing

and configuring Dialogic products. If you are unsure

how to contact your support channel, please call

Dialogic in the United States at 973-967-6600 (9am -

5pm EST) and we will assist in obtaining the

appropriate support channel. Outside the United

States please refer to

http://www.dialogic.com/support/contact to obtain

local contact information.

Dialogic also provides direct support via Dialogic®

Pro™ Services agreements. For more details of direct

support from Dialogic please refer to

http://www.dialogic.com/support/DialogicPro.

10.Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following:

http://www.dialogic.com/support/hwfaults

Dialogic

is a registered trademark of Dialogic Corporation.

Dialogic's trademarks may be used publicly only with

permission from Dialogic. Such permission may only be

granted by Dialogic's legal department. The names of actual

companies and products mentioned herein are the

trademarks of their respective owners.