HP Xw460c - ProLiant - Blade Workstation Handbuch zur Umsetzung - Seite 29

Blättern Sie online oder laden Sie pdf Handbuch zur Umsetzung für Schalter HP Xw460c - ProLiant - Blade Workstation herunter. HP Xw460c - ProLiant - Blade Workstation 35 Seiten. Mezzanine card installation instructions for supported hp proliant c-class bladesystem servers
Auch für HP Xw460c - ProLiant - Blade Workstation: Handbuch zur Fehlervermeidung (12 seiten), Technisches Weißbuch (12 seiten), Firmware-Aktualisierung (9 seiten), Installationshandbuch (2 seiten), Handbuch für häufig gestellte Fragen (14 seiten), Poster einrichten (9 seiten), Installationshandbuch (33 seiten), Management-Handbuch (28 seiten), Hardware-Handbuch (23 seiten), Übersicht (35 seiten), Benutzerhandbuch (33 seiten), Handbuch für die Optimierung (13 seiten), Eingeschränkte Garantie (10 seiten), Installationsanleitung Handbuch (10 seiten), Installationsanleitung Handbuch (8 seiten), Einbauanleitung (4 seiten), Einbauanleitung (2 seiten)

Seite drucken

HP Xw460c - ProLiant - Blade Workstation Handbuch zur Umsetzung

Issue 7

Anomalies associated with adding EISA/ISA bus options

Description

Solution

Issue 8

Windows 2000 does not detect changes to the IRQ of EISA devices

Description

Solution

Issue 9

Some HP server USB hardware displays as unsupported USB connector in Device Manager

Description

Solution

Issue 10

CPQARRAY.SYS and CPQARRY2.SYS cause timeout error messages in the event log at startup

Description

Solution

After hot plugging a hard drive in a storage drive bay, selecting Rescan Disks

might result in Windows 2000 failing to identify the drive and displaying this

error message:

"Unsafe Removal of Device: You have unplugged or ejected a device without

stopping it. Unplugging or ejecting a device without first stopping them can

often cause the computer to crash or lose valuable data. To safely unplug or

eject any of the following devices, first use the Hardware Wizard in the Control

Panel to stop the device..."

Windows 2000 does not detect changes to the IRQ of EISA devices.

Changing the interrupt associated with the SMART 2/E Array Controller as the

booting device is not supported.

Please check the resource settings in system configuration before exchanging

a faulty controller. On the new SMART 2/E Array Controller, all resources

must be set the same as they were on the SMART 2/E Array Controller being

replaced.

The SMART 2/E Array Controller is an Extended Industry Standard

Architecture (EISA) controller and not a Plug and Play (PnP) architecture

controller. Windows 2000 uses PnP, which cannot detect and change the

resource settings for an EISA controller. Windows 2000 expects to find the

SMART 2/E Array Controller at the memory address and Interrupt Request

(IRQ) number specified when the original SMART 2/E Array controller was

installed.

Some HP server USB hardware displays as unsupported USB connector in

Device Manager.

Some HP servers display a yellow exclamation mark in the Windows 2000

Device Manager. This is expected behavior. These HP servers were not

designed to implement the USB functionality and no problem actually exists.

CPQARRAY.SYS and CPQARRY2.SYS cause timeout error messages in the

event log at startup.

At startup, CPQARRAY.SYS and CPQARRY2.SYS cause timeout error messages

in the event log. A message may be displayed in the event log that reads:

CPQARRY2 - device\SCSI\CPQARRY21 is not ready for access.

The device, \Device\Scsi\Cpqarray2, did not respond within the timeout

period.

These messages may safely be ignored (loading the drivers and initializing all

attached devices takes more time than Windows 2000 expects). Despite the

timeout messages, the drivers do install and the controllers function correctly.