HP Xw460c - ProLiant - Blade Workstation Installationshandbuch - Seite 32

Blättern Sie online oder laden Sie pdf Installationshandbuch für Schalter HP Xw460c - ProLiant - Blade Workstation herunter. HP Xw460c - ProLiant - Blade Workstation 33 Seiten. Mezzanine card installation instructions for supported hp proliant c-class bladesystem servers
Auch für HP Xw460c - ProLiant - Blade Workstation: Handbuch zur Umsetzung (35 seiten), Handbuch zur Fehlervermeidung (12 seiten), Technisches Weißbuch (12 seiten), Firmware-Aktualisierung (9 seiten), Installationshandbuch (2 seiten), Handbuch für häufig gestellte Fragen (14 seiten), Poster einrichten (9 seiten), Management-Handbuch (28 seiten), Hardware-Handbuch (23 seiten), Übersicht (35 seiten), Benutzerhandbuch (33 seiten), Handbuch für die Optimierung (13 seiten), Eingeschränkte Garantie (10 seiten), Installationsanleitung Handbuch (10 seiten), Installationsanleitung Handbuch (8 seiten), Einbauanleitung (4 seiten), Einbauanleitung (2 seiten)

Seite drucken
HP Xw460c - ProLiant - Blade Workstation Installationshandbuch

SNMP configuration parameters

If you are using SNMP, record the configuration parameters in the following table.
Table 4-1 1 Onboard Administrator SNMP configuration parameters
Parameter
System location
System contact
Read community
Write community
SNMP alert destination IP
address
SNMP alert destination
community string

Power management configuration parameters

Record the configuration parameters in the following table.
Table 4-12 Onboard Administrator power management configuration parameters
Parameter
Enclosure Power mode
Dynamic Power Savings mode
Enable Enclosure AC Input
Watts Limit
Enclosure Input Watts Limit
SNMP alert destination IP
address
SNMP alert destination
community string
32
Onboard Administrator installation configuration parameters
Value
Value
Possible value
0 to 20 characters, including
alphanumeric, dash,
underscore, and space
0 to 20 characters, including
alphanumeric, dash,
underscore, and space
0 to 20 characters, including
alphanumeric, dash, and
underscore
0 to 20 characters, including
alphanumeric, dash, and
underscore
###.###.###.###, where ###
ranges from 0 to 255
0 to 20 characters, including
alphanumeric, dash, and
underscore
Possible value
AC Redundant, Power Supply
Redundant, or Not Redundant
Yes or No
Yes or No
2,700 VA to 16,400 VA
###.###.###.###, where ###
ranges from 0 to 255
0 to 20 characters, including
alphanumeric, dash, and
underscore
Description
The SNMP location of the
enclosure
The name of the system contact
The read community name.
Default: public.
The write community name.
Default: blank.
The management station IP
address
A text string that acts as a
password that authenticates
messages sent between HP SIM
and HP Onboard Administrator
Description
The chosen redundant operation
mode for the power subsystem
Yes is the default value because
the dynamic power mode saves
power in most situations. When
enabled, Dynamic Power Server
mode runs the required power
supplies at a higher rate of use.
Unused power supplies remain
in standby mode.
—
If a data center has a cooling
capacity limitation for the
maximum number of VA (watts)
that can be cooled per
enclosure, set a VA limit.
Cooling capacity information
can be obtained from your
facilities manager. Setting the
Input VA limit to less than the
maximum VA supplied by the
selected power supply mode
limits the number of devices that
can be powered up and keeps
the enclosure within the cooling
capacity of the data center.
The management station IP
address
A text string that acts as a
password that authenticates
messages sent between HP SIM
and HP Onboard Administrator