Accusplit Eagle AE170XL Betriebsanleitung - Seite 3
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Schrittzähler Accusplit Eagle AE170XL herunter. Accusplit Eagle AE170XL 4 Seiten. Accusplit fitness electronics user manual
Seite drucken
WEARING YOUR PEDOMETER
Gently slide the pedometer
onto your belt or the top
edge of your pants or skirt.
It should fit snugly and
level, above one knee. T he
strong steel clip makes it
easy.
Note: T he pedometer should be as vertical as possible.
Walkers with larger stomachs may find it helpful to
wear the pedometer farther back on the body, toward
one hip.
The cover must be closed for the pedometer to work.
16
First, loop leash
through slot on side
of pedomete
r
Next, clasp clothing
Or, loop a belt
or belt loop
18
RESETTING YOUR PEDOMETER
Most people prefer to reset counts daily. T o reset your counts:
From STEP , DISTANCE, or CALORIE mode, press and hold
the yellow RESET button for at least 2 seconds. Y ou'll see the
values all go back to zero.
20
Can be set
from 0-5
steps
"US" (English)
or "EU" (Metric)
-
D
W
XL
IGI
ALKER
.COM
STEP
DIST CAL
SET
XL
170
JW200
S3-
S1,S2,S4
S3+
22
Set measurement mode
yes
no
Or, loop a
badge holder, then
put into pocket
(Badge holder
not included)
-
D
W
XL
IGI
ALKER
.COM
STEP
DIST CAL
SET
XL
170
JW200
S3-
S1,S2,S4
S3+
Set Step Filter set point
To avoid losing or dropping your pedometer, use the included
leash and clip to fasten the pedometer securely to your
clothing.
Attaching the Leash
1. Attach the pedometer to the leash by looping the thin
side of the leash through one of the leash slots on the
sides of the pedometer case, near the bottom of the unit.
2. Put the pedometer onto your clothing as discussed above.
3. Attach the alligator clip to a belt loop or the top edge of the
pants or skirt.
Note: Y ou can also use a safety pin to fasten the leash to
your clothing, loop the leash through your belt or belt
loop, or use a badge holder.
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, it
will automatically begin to record your steps, activity time,
distance, and calories burned. Repeatedly press the MODE
button to cycle through the pedometer modes:
STEPS g DISTANCE g CALORIE g STEPS
Distance and Calories are counted automatically whenever
steps are being counted.
• DISTANCE is simply stride length x steps.
• CALORIES is calorie burn from activity based on
your weight and rate of stepping pace.
Note: For extra accuracy, the default Step Filter Setting is 1.
See page 21 to learn more.
OTHER SETTINGS
The Step Filter and Unit of Measurement settings are
accessed through a special "deep set" mode.
To enter this mode, press and hold the S1 button for 4
seconds. T he screen will display a single digit. From within
Deep Set mode, press the S2 button to cycle back and forth
between the Step Filter set point and Choice of Unit System.
CHANGING STEP FILTER SETTING
While the JW200 PedometerEngine™ Step Sensor is
extremely accurate, some people like to have the ability to
filter out false steps. T herefore, the unit has a variable setting
step filter, to allow fine-tuning to your specific preferences.
You can set the value to any value from 0 – 5 steps. For
example, if the filter is set to "3" , the unit will wait to start
counting steps until more than three steps have been taken in
less than five seconds.
Press S3+ (MODE) or S3– (RESET) to change the Step Filter
Setting.
17
19
21
23