Caberg Just SpeakS Benutzerhandbuch - Seite 9

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Zubehör für Motorräder Caberg Just SpeakS herunter. Caberg Just SpeakS 14 Seiten. Bluetooth headset & intercom for scooters and motorcycles

Seite drucken

JUST SPEAK S

INTERCOM CONVERSATION

6. INTERCOM CONVERSATION

Pairing with Other Just Speak S Headsets for

Intercom Conversation

The Just Speak S can be paired with another headset for Bluetooth

intercom conversation.

1. Turn on the two Just Speak S headsets (A and B) that you would like to

pair with each other.

2. Press and hold the (-) Button of the headset A and B for 5 seconds until

the red LEDs of both units start to flash rapidly. You will hear a voice

prompt saying "Intercom pairing".

3. Simply press the (-) Button of either of the two headsets A or B (It doesn't

matter that you choose A or B) and wait until the LEDs of both headsets

turn to blue and intercom connection is automatically established. The

two Just Speak S headsets A and B are paired with each other for

intercom conversation. If the pairing process is not completed within

one minute, the Just Speak S will return to stand-by mode.

Starting and Ending Intercom Conversation

1. You can start an intercom conversation with your intercom friend by

pressing and holding the (-) Button for 1 second.

2. To terminate an intercom conversation, press and hold the (-) Button for

1 second again.

Intercom and Mobile Phone Call

1. When you have an incoming mobile phone call during an intercom

conversation, you will hear a ring tone. You can choose whether to 1)

answer the mobile phone call and stop the intercom conversation, or 2)

reject the phone call and stay on the intercom conversation.

• To answer the phone call and stop the intercom conversation, press

the (+) Button. When you hang up the phone call, the intercom will

automatically be recovered.

• To reject the phone call and stay on the intercom conversation, press

and hold the (-) Button for 2 seconds until you hear a beep.

Unlike other motorcycle Bluetooth headsets, this prevents a user from

being dropped out of an intercom conversation by an incoming mobile call.

2. When you have an incoming intercom call during a mobile phone call,

you will hear 4 high tone beeps, alerting you that there is an incoming

intercom call. You will also hear a voice prompt saying "Intercom

requested". In this case, the intercom call does not override the mobile

phone call because intercom has lower priority than mobile call. You

have to hang up the mobile phone call to make or receive an intercom

call.

Intercom Failure

When you try to start an intercom conversation with an intercom friend who

is already having a mobile phone call with another person, you will hear a

low tone double beep signifying a busy signal. You will also hear a voice

prompt saying "Intercom failed, try again later". In this case, you have to

try again later. On the other hand, the intercom friend will hear 4 high tone

beeps alerting them that there is an incoming intercom call.

Intercom Reconnection

If your intercom friend goes out of range while having an intercom

conversation, you may hear static noise and eventually the intercom will be

disconnected. In this case, the Just Speak S automatically tries to reconnect

the intercom every 8 seconds. You will hear high tone double beeps until the

intercom is reestablished. If you don't want to make a reconnection, press

and hold the (-) Button for 1 second to stop the attempt.

JUST SPEAK S

Just Speak S CONFIGURATION SETTING

7. JUST SPEAK S CONFIGURATION SETTING

You can set the configuration of the Just Speak S by the voice menu

instruction as below.

1. To enter into voice configuration menu, press and hold the (+) Button

for 10 seconds until the LED shows solid blue and you hear high tone

double beeps. You will hear a voice prompt saying "Configuration

menu".

2. Press the (+) Button to navigate between menus. You will hear voice

prompts for each menu items as below.

3. You can enable or disable the feature or execute the command by

pressing the (-) Button.

4. If any button is not pressed within 10 seconds, the Just Speak S will exit

the configuration and goes back to standby.

5. If you want to exit the configuration immediately, press and hold the (+)

Button until you hear a voice prompt, "Exit configuration", and press

the (-) Button.