Sony MEX-BT39UW Datensatz des Eigentümers - Seite 40
Blättern Sie online oder laden Sie pdf Datensatz des Eigentümers für Stereo System Sony MEX-BT39UW herunter. Sony MEX-BT39UW 45 Seiten. Bluetooth audio system
Auch für Sony MEX-BT39UW: Spezifikationsblatt (4 seiten), Installation/Verbindungen (2 seiten), Service-Handbuch (48 seiten)
Seite drucken
®
Bluetooth
Audio System
Installation/Connections
Instalación/Conexiones
MEX-BT39UW
©2010 Sony Corporation Printed in Thailand
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
Front speaker
Altavoz frontal
Rear speaker
Altavoz posterior
Active subwoofer
Altavoz potenciador de
graves activo
4-199-773-41(1)
× 2
× 4
Microphone XA-MC10
Micrófono XA-MC10
Power amplifier
Amplificador de potencia
A
SUB OUT ( MONO )
B
BUS AUDIO IN
Satellite radio tuner
(XM/SIRIUS)*
Sintonizador de radio por satélite
(XM/SIRIUS)*
BUS CONTROL IN
Cautions
Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts Iist
The numbers in the list are keyed to those in the
instructions.
The bracket attached to the unit before shipping.
Before mounting the unit, use the release keys to
remove the bracket from the unit. For details, see
"Removing the bracket ()" on the reverse side of the
sheet.
Keep the release keys for future use as they are
also necessary if you remove the unit from your
car.
Caution
Handle the bracket carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of the bracket
are bent inwards 2 mm (
3
/
in). If the catches are straight or bent
32
outwards, the unit will not be installed securely and may spring out.
FRONT
AUDIO OUT
REAR
AUDIO OUT
* not supplied
no suministrado
Connection example
Notes (-A)
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
Note on satellite radio tuner (-B)
This unit does not support the XM radio tuner
XMDSON100.
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see "Notes on the control and power supply leads."
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
To the interface cable of a car telephone
To the +12 V power terminal which is energized
in the accessory position of the ignition switch
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see "Notes on the control and power supply leads."
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.