Cisco 3800 Series Benutzerhandbuch - Seite 5
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Gateway Cisco 3800 Series herunter. Cisco 3800 Series 7 Seiten. Password recovery procedure
Auch für Cisco 3800 Series: Datenblatt (8 seiten), Anwendungshinweis (41 seiten), Handbuch zur Fehlersuche (15 seiten), Datenblatt (20 seiten), Schnellstart-Handbuch (40 seiten), Konfigurieren von (32 seiten)
Seite drucken
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non−volatile configuration memory.
8192K bytes of processor board System flash partition 1 (Read/Write)
8192K bytes of processor board System flash partition 2 (Read/Write)
−−− System Configuration Dialog −−−
Would you like to enter the initial configuration dialog? [yes/no]: n
Press RETURN to get started!
00:00:19: %LINK−3−UPDOWN: Interface BRI0/0, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Ethernet0/0, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Ethernet0/1, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Serial0/0, changed state to down
00:00:19: %LINK−3−UPDOWN: Interface Serial0/1, changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0,
changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/0,
changed state to up
Router>
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/1,
changed state to up
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Serial0/0,
changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Serial0/1,
changed state to down
00:00:50: %SYS−5−RESTART: System restarted −−
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600−IS−M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
Copyright (c) 1986−1999 by cisco Systems, Inc.
Compiled Tue 07−Dec−99 02:21 by phanguye
00:00:50: %LINK−5−CHANGED: Interface BRI0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Ethernet0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Serial0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Ethernet0/1,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Serial0/1,
changed state to administratively down
00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/0,
changed state to down
00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/1,
changed state to down
Router>
Router>enable
Router#copy startup−config running−config
Destination filename [running−config]?
1324 bytes copied in 2.35 secs (662 bytes/sec)
Router#
00:01:24: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0:1,
changed state to down
00:01:24: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0:2,
changed state to down
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret < password >