Cisco 3800 Series Manual do utilizador - Página 5
Procurar online ou descarregar pdf Manual do utilizador para Porta de entrada Cisco 3800 Series. Cisco 3800 Series 7 páginas. Password recovery procedure
Também para Cisco 3800 Series: Ficha de dados (8 páginas), Nota de aplicação (41 páginas), Manual de resolução de problemas (15 páginas), Ficha de dados (20 páginas), Manual de início rápido (40 páginas), Configuração (32 páginas)
Imprimir página
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non−volatile configuration memory.
8192K bytes of processor board System flash partition 1 (Read/Write)
8192K bytes of processor board System flash partition 2 (Read/Write)
−−− System Configuration Dialog −−−
Would you like to enter the initial configuration dialog? [yes/no]: n
Press RETURN to get started!
00:00:19: %LINK−3−UPDOWN: Interface BRI0/0, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Ethernet0/0, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Ethernet0/1, changed state to up
00:00:19: %LINK−3−UPDOWN: Interface Serial0/0, changed state to down
00:00:19: %LINK−3−UPDOWN: Interface Serial0/1, changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0,
changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/0,
changed state to up
Router>
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/1,
changed state to up
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Serial0/0,
changed state to down
00:00:20: %LINEPROTO−5−UPDOWN: Line protocol on Interface Serial0/1,
changed state to down
00:00:50: %SYS−5−RESTART: System restarted −−
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600−IS−M), Version 12.0(7)T, RELEASE SOFTWARE (fc2)
Copyright (c) 1986−1999 by cisco Systems, Inc.
Compiled Tue 07−Dec−99 02:21 by phanguye
00:00:50: %LINK−5−CHANGED: Interface BRI0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Ethernet0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Serial0/0,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Ethernet0/1,
changed state to administratively down
00:00:52: %LINK−5−CHANGED: Interface Serial0/1,
changed state to administratively down
00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/0,
changed state to down
00:00:53: %LINEPROTO−5−UPDOWN: Line protocol on Interface Ethernet0/1,
changed state to down
Router>
Router>enable
Router#copy startup−config running−config
Destination filename [running−config]?
1324 bytes copied in 2.35 secs (662 bytes/sec)
Router#
00:01:24: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0:1,
changed state to down
00:01:24: %LINEPROTO−5−UPDOWN: Line protocol on Interface BRI0/0:2,
changed state to down
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret < password >