aeolus UC-1803 Schnellstart-Handbuch - Seite 7

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Zubehör aeolus UC-1803 herunter. aeolus UC-1803 12 Seiten. Professional vet equipments supplier

Seite drucken

2. Temperature display

Figure 7.2.1

3. Humidity / CO

Concentration Display

Humidity / CO

concentration display can be switched

with the humidity / CO

concentration key. The default

is humidity display in two-digit integer and one

decimal place. CO

concentration is displayed in

four-digit integer. Switch the humidity / CO

concentration indicator lamp. When the Indicator

lamp is "HU", it means humidity; when the indicator

lamp is "CO

", it means CO

concentration. See fig.

7.3.1.

4. Temperature Control Part

Key control: press "SET" key plus temperature "+/_" key at the same time to adjust the temperature set

point, and regulate it by ± 0.1 stepping. See fig. 7.4.1.The factory setting is the set point of 20°C. It can be

adjusted down to 15°C and up to 38°C;

Smart alarm function:

Alarm for beyond the maximum set point: the temperature and the upper dash are displayed alternately

every three seconds with alarm and flashing temperature indicator lamp.

Alarm for beyond the minimum set point: the tempera-

ture and the lower dash are displayed alternately every

three seconds with alarm and flashing temperature

Indicator lamp.

Damaged temperature sensor: flashing "ERR" display

and flashing temperature indicator lamp in the

temperature display.

Fahrenheit/centigrade can be switched and

displayed with a toggle key. The default tempera-

ture is shown in centigrade and in two-digit integer

and one decimal place after which is a letter

showing special indication at the time of setting the

temperature parameter. Switch the Fahrenheit/cen-

tigrade indicator lamp. When the indicator lamp

displays "C", it means centigrade; when it displays

"F", it means Fahrenheit. See fig. 7.2.1.

Figure 7.3.1

Hold

Figure 7.4.1

Control program:

a) When the setting temperature is higher than the measured temperature, start the PID precise heating

system and left/right fans. When the measured temperature is higher than the setting temperature, stop

heating step by step.

b) When the measured temperature is higher than the setting temperature, start the PID precise cooling

system (need additionally purchased cooler) and the left fan to realize ventilation and air exchange inside

and outside. When the measured temperature is lower than the setting temperature, stop cooling step by

step and shut down fans after one-minute delay.

c) When there is no additionally connected cooler, try to place an ice tube inside the atomizing chamber or

at the sink as auxiliary cooling. The system will start the right fan and the left fan to realize ventilation and

cooling.

Indicator lamp control:

Heating---the temperature indicator lamp is red

Cooling---the temperature indicator lamp is blue

Delay---the temperature indicator lamp is yellow

5. Humidity Control Part

Key control: press "SET" key plus humidity "+/-" key

at the same time to adjust the humidity set point, and

regulate it by±0.1 stepping. See fig. 7.4.1. The factory

setting is the humidity set point of 55%. It can be

adjusted down to 40% and up to 65%.

Alarm function:

a) Alarm for beyond the maximum set point: the

humidity and the upper dash are displayed alternate-

ly every three seconds with alarm and flashing

temperature indicator lamp.

b) Alarm for beyond the minimum set point: the

humidity and the lower dash are displayed alternately every three seconds with alarm and flashing tempera-

ture indicator lamp.

c) Damaged humidity sensor: flashing "ERR" display and flashing humidity indicator lamp in the humidity

display.

d) Humidifier water shortage alarm (the water level sensor of the humidifier is disconnected): in this case, if

the humidifier is started, the humidity Indicator lamp is off with water shortage alarm, and the humidity

display shows "LAC". Meanwhile, it starts the smart water shortage protection system.

Control program:

a) When the setting humidity is higher the measured humidity, start the humidifier and the right fan.

b) When the measured humidity reaches the setting humidity, stop humidifying.

c) When the measured humidity is higher than the setting humidity, start dehumidifying and the left fan;

reversely start the right fan for air exhaust as auxiliary dehumidifying. If an additionally purchased cooler is

connected, start the cooling function for dehumidifying.

Indicator lamp control:

The humidity indicator lamp is always on at the time of humidifying.

The humidity indicator lamp is flashing at the time of dehumidifying.

Hold

Figure 7.5.1