Aeon Labs Home Energy Meter Anweisungen

Blättern Sie online oder laden Sie pdf Anweisungen für Messgeräte Aeon Labs Home Energy Meter herunter. Aeon Labs Home Energy Meter 2 Seiten. Z-wave home energy meter

Seite drucken

Aeon Labs Home Energy Meter

(Z-Wave Home Energy Meter)

Introduction:

The Aeon Labs Home Energy Meter is energy meter for the

entire home. It can wirelessly report immediate wattage

and kWh usage of the AC mains to a Z-Wave gateway.

By taking advantage of the Z-Wave mesh network,

commands can be routed to their destination via

intermediary "listening" Z-Wave products. Products that

are Z-Wave certified can be used and communicate with

other Z-Wave certified devices.

Z-Wave Network Instructions:

The Aeon Labs Home Energy Meter must be paired

(included) into a Z-Wave network before it can receive Z-

Wave commands to report its energy usage. The home

energy meter can only communicate to devices within it's

own z-wave network.

Note: If the Home Energy Meter is not currently paired into

a Z-Wave network, the LED on the Home Energy Meter will

blink after pressing the button located near the batteries.

- 1 -

Adding/Including/Pairing the Home Energy Meter

•

into a Z-Wave Network

Press the button on the Aeon Labs Z-Stick to begin the

Z-Wave inclusion process.

Press the button labeled "Include" on the Aeon Labs

Minimote to begin the Z-Wave inclusion process.

Note: To include the Aeon Labs Home Energy Meter

with other controllers, please consult the operation

manual for these controllers on how to include Z-

Wave products into an existing network.

instructions on select partner gateways, visit

www.aeon-labs.com/support.

After placing 4 AA batteries into the Home Energy

Meter, press the button located near the batteries .

Troubleshooting: If the Aeon Labs Home Energy Meter was

not successfully included into any Z-Wave network, the LED

will blink after pressing the button near the batteries. If the

Aeon Labs Home Energy Meter was successfully included to

a Z-Wave network, the LED will be lit solid after pressing the

button.

- 2 -

Removing/Excluding/Resetting the Home Energy

•

Meter from your Z-Wave Network

Hold the button on the Aeon Labs Z-Stick to begin the

Z-Wave removal process.

Press the button labeled "Remove" on the Aeon Labs

Minimote Stick to begin the Z-Wave removal process.

Note: To include the Aeon Labs Home Energy Meter

with other controllers, please consult the operation

manual for these controllers on how to include Z-

Wave products into an existing network.

instructions on select partner gateways, visit

For

www.aeon-labs.com/support.

After placing 4 AA batteries into the Home Energy

Meter, press the button located near the batteries .

Troubleshooting: If the Aeon Labs Home Energy Meter was

removed from the Z-Wave network, the LED will blink after

pressing the button near the batteries. If the Aeon Labs

Home Energy Meter was not successfully removed from a

Z-Wave network, the LED will be lit solid after pressing the

button.

- 3 -

Power by an USB/AC Adapter

•

While the Aeon Labs Home Energy Meter can operate for

nearly a year on batteries, it can also be powered through

it's USB port. While powered by the USB port, the Home

Energy Meter can track kWh energy usage and report

wattage every few seconds.

AC Mains Installation

•

IMPORTANT: It is recommened that a licensed electrician

assist with the installation as you must open the main

circuit box (usually located outside of your house).

After opening the main circuit box panel, clip each of the

clamps of the Aeon Labs Home Energy Meter around the

For

two incoming wires that connect to the main circuit breaker

from the main wire going into the box.

If you have purchased the optional Home Energy Meter AC

Adapter, you may insert one of the AC adapters exposed

wires into one of the neutral bus terminals and the other

exposed wire into the live terminals coming from the main

circuit breaker.

Note: Some AC Mains boxes are made of metal and may

reduce the radio communication power from the Home

Energy Meter to other Z-Wave devices within the house. To

improve radio performance, the Home Energy Meter may

be placed outside of the main circuit box. The Home Energy

Meter is IP43 weatherized to be resistant to rain and snow

when placed vertically with the wires protruding from the

bottom of the unit.

- 4 -