Pioneer NC-50DAB Gebrauchsanweisung - Seite 36

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Auto-Empfänger Pioneer NC-50DAB herunter. Pioneer NC-50DAB 42 Seiten. Network cd receiver

Seite drucken

> Before Start

> Part Names

Troubleshooting

Others

Before starting the procedure

When operation is unstable, problems may be solved by

simply turning the power on or to standby or disconnecting/

connecting the power cord, rather than reviewing settings

and operations. Try the simple measures on both the unit

and the connected device. If the problem isn't fixed after

referring to "Troubleshooting", resetting the unit to the

status at the time of shipment may solve the problem. Note

that your settings will also be initialized when you reset, so

we recommend that you note down your settings before

doing the following.

Resetting the unit (this resets the unit settings to

the default)

1. Press SETUP on the remote controller, select "Factory

Reset" - "Start" in the Setup screen and press ENTER.

2. Press ENTER.

3. The unit switches to standby and the settings are reset.

Power

Cannot turn on the unit

0 Unplug the power cord from the wall outlet, wait 5

seconds or more, then plug it in again.

The unit turns off unexpectedly

0 The unit automatically switches to standby when the

"Option Setting" - "Power Off Setting" - "Auto Standby"

setting in the Setup menu functions.

0 Check if the speaker cable wires are touching the rear

panel or if the i side and s side have shorted. If there is

contact or shorting, the unit will switch to standby

automatically.

0 If the power turns off and indicators on the front panel

continually blink, there may have been a malfunction with

the amplifier or the protection circuit may have tripped.

– If the power indicator blinks at approximately 1 second

intervals: There may have been a malfunction in the

> Install

> Initial Setup

amplifier section. Unplug the power cord from the wall

outlet immediately and contact the dealer or our

company's support.

– If the power indicator blinks at approximately 0.3

second intervals: The protection circuit may have

tripped due to playback at high volume. Reduce the

volume for playback. Alternatively, the wires in the

speaker cables may have touched the rear panel or

other wires. Connect the wires so they do not protrude

from the speaker jacks.

If the same symptoms such as being unable to turn the

unit on happen repeatedly, unplug the power cord from

the wall outlet immediately and contact the dealer or our

company's support.

There is no audio from external devices

0 There is no sound if this unit is muted. Press MUTE on

the remote controller to cancel muting.

0 Confirm that the connection between the output jack on

the external device and the input jack on this unit is

correct.

0 Change the input selector on this unit to the position of

the terminal to which the external device is connected.

0 Check the digital audio output setting on the connected

component. On some game consoles, such as those that

support DVD, the default setting is off.

The display doesn't light

0 The display may go dim while the DIMMER is working,

and may also turn off. Press DIMMER button and change

the brightness level of the display.

Wi-Fi Connection

0 Try plugging/unplugging the power supply of wireless

LAN router and the unit, check the wireless LAN router

> Playback

Advanced Setup | Firmware Update |

power-on status, and try reboot of the wireless LAN

router.

Cannot connect to the access point

0 Check that the setting of SSID and encryption (WEP,

etc.) is correct. Make sure the network settings of the unit

is properly set.

0 Connection to an SSID that includes multi-byte

characters is not supported. Name the SSID of the

wireless LAN router using single-byte alphanumeric

characters only and try again.

0 When the wireless LAN router setting is at stealth mode

(mode to hide the SSID key) or when ANY connection is

off, the SSID is not displayed. Change the setting and try

again.

Connected to an SSID different to the SSID selected

0 Some access points allow you to set multiple SSIDs for

one unit. If you use the automatic setting button on such

a router, you may end up connecting with a different

SSID from the SSID you wanted to connect to. Use the

connection method requiring you to enter a password if

this happens.

Playback is interrupted and communication does not

work

0 Shorten the distance from the access point or remove

obstacles to improve visibility, and try again. Place the

unit away from microwave ovens or other access points.

It is recommended to place the access point and the unit

in the same room.

0 If there is a metallic object near the unit, wireless LAN

connection may not be possible as the metal can effect

on the radio wave.

0 When other access point are used near the unit, several

issues such as interrupted playback and communication

may occur. You can avoid these issues by changing the

channel of the access point. For instructions on changing

channels, see the instruction manual provided with the

access point.

Others