Pioneer Super Tuner IIID AVH-P4000DVD Installationshandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Installationshandbuch für Auto-Empfänger Pioneer Super Tuner IIID AVH-P4000DVD herunter. Pioneer Super Tuner IIID AVH-P4000DVD 8 Seiten. Pioneer avh-p4000dvd: install guide
Auch für Pioneer Super Tuner IIID AVH-P4000DVD: Installationshandbuch (6 seiten)

Seite drucken

Pioneer Super Tuner IIID AVH-P4000DVD Installationshandbuch

Connecting the units

Connecting the power cord

Note:

Depending on the kind of vehicle, the

This product

function of 3* and 5* may be different. In

this case, be sure to connect 2* to 5* and

4* to 3*.

Antenna input

Fuse (10 A)

Connect leads of the same

color to each other.

Cap (1*)

Do not remove cap if this

terminal is not in use.

Yellow (3*)

Yellow (2*)

Back-up

Connect to the constant 12 V

(or accessory)

supply terminal.

Fuse resistor

Red (5*)

Red (4*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

Orange/white

Fuse resistor

Connect to lighting switch terminal.

Black (chassis ground)

Connect to a clean, paint-free metal location.

ISO connector

Speaker leads

Front left 

Note:

White:

White/black: Front left 

In some vehicles, the ISO connector may be

Front right 

Gray:

divided into two. In this case, be sure to connect

Front right 

to both connectors.

Gray/black:

Rear left  or subwoofer 

Green:

Green/black: Rear left  or subwoofer 

When you connect the separately sold

Rear right  or subwoofer 

Violet:

multi-channel processor (e.g., DEQ-P6600) to

Rear right  or subwoofer 

Violet/black:

this unit, do not connect anything to the

speaker leads and system remote control

(blue/white).

Connecting the units

Yellow/black

If you use equipment with Mute function, wire this lead to the

Audio Mute lead on that piece of equipment. If not, keep the

Audio Mute lead free of any connections.

Connection method

1. Clamp the lead.

2. Clamp firmly with

needle-nosed pliers.

Note:

· The position of the parking brake switch depends on the vehicle model. For details,

consult the vehicle Owner's Manual or dealer.

Light green

Used to detect the ON/OFF status of the parking brake. This lead

must be connected to the power supply side of the parking brake

switch.

Blue/white

Parking brake

Connect to system control terminal of the power

switch

Power supply side

amp (max. 300 mA 12 V DC).

Ground side

Blue/white (7*)

Blue/white (6*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO

connector will differ depending on

Notes:

the type of vehicle. Connect 6* and

· Change the initial setting of this unit (refer to the Operation Manual).

7* when Pin 5 is an antenna control

The subwoofer output of this unit is monaural.

· When using a subwoofer of 70 W (2 Ω) , be sure to connect with

type. In other types of vehicles,

never connect 6* and 7*.

Violet and Violet/black leads of this unit. Do not connect anything to

Green and Green/black leads.

Connecting the units

When connecting to separately sold power amp

This product

Power amp

(sold separately)

Power amp

(sold separately)

Front output

Connect with RCA cables (sold

Rear output or

separately)

subwoofer output

Blue/white

Connect to system control

terminal of the power amp

(max. 300 mA 12 V DC).

System remote control

Blue/white (7*)

Blue/white (6*)

Connect to auto-antenna

relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect 6*

Left

Right

and 7* when Pin 5 is an antenna control type.

In other types of vehicles, never connect 6* and

7*.



When you connect the separately sold

Front speaker

multi-channel processor (e.g., DEQ-P6600) to



this unit, do not connect anything to the

speaker leads and system remote control



(blue/white).

Rear speaker

or Subwoofer



or Subwoofer

When you connect the multi-channel processor

to this unit, refer to multi-channel processor's

installation manual for the connection method.

Perform these connections when

Note:

using the optional amplifier.

· Change the initial setting of this unit

(refer to the Operation Manual).

The subwoofer output of this unit is monaural.

Connecting the units

Connecting the system

USB cable

Connect to sparately sold

USB device.

1.5 m

This product

20 cm

Multi-CD player

iPod with Dock

(sold separately)

connector

Wired remote input

Gray

Hard-wired remote control

Dock connector

adaptor can be connected

2 m

(sold separately).

Interface cable

(e.g., CD-I200) (sold separately)