Pioneer Super Tuner IIID AVH-P4000DVD Manuel d'installation - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Pioneer Super Tuner IIID AVH-P4000DVD. Pioneer Super Tuner IIID AVH-P4000DVD 8 pages. Pioneer avh-p4000dvd: install guide
Également pour Pioneer Super Tuner IIID AVH-P4000DVD : Manuel d'installation (6 pages)
Imprimer la page
Connecting the units
Connecting the power cord
Note:
Depending on the kind of vehicle, the
This product
function of 3* and 5* may be different. In
this case, be sure to connect 2* to 5* and
4* to 3*.
1*
3*
2*
Antenna input
Fuse (10 A)
5*
4*
Connect leads of the same
color to each other.
Cap (1*)
Do not remove cap if this
terminal is not in use.
Yellow (3*)
Yellow (2*)
Back-up
Connect to the constant 12 V
(or accessory)
supply terminal.
Fuse resistor
Red (5*)
Red (4*)
Accessory
Connect to terminal controlled by
(or back-up)
ignition switch (12 V DC).
Orange/white
Fuse resistor
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
ISO connector
Speaker leads
Front left
Note:
White:
White/black: Front left
In some vehicles, the ISO connector may be
Front right
Gray:
divided into two. In this case, be sure to connect
Front right
to both connectors.
Gray/black:
Rear left or subwoofer
Green:
Green/black: Rear left or subwoofer
When you connect the separately sold
Rear right or subwoofer
Violet:
multi-channel processor (e.g., DEQ-P6600) to
Rear right or subwoofer
Violet/black:
this unit, do not connect anything to the
speaker leads and system remote control
(blue/white).
Connecting the units
Yellow/black
If you use equipment with Mute function, wire this lead to the
Audio Mute lead on that piece of equipment. If not, keep the
Audio Mute lead free of any connections.
Connection method
1. Clamp the lead.
2. Clamp firmly with
needle-nosed pliers.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner's Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch.
Blue/white
Parking brake
Connect to system control terminal of the power
switch
Power supply side
amp (max. 300 mA 12 V DC).
Ground side
Blue/white (7*)
Blue/white (6*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO
connector will differ depending on
Notes:
the type of vehicle. Connect 6* and
· Change the initial setting of this unit (refer to the Operation Manual).
7* when Pin 5 is an antenna control
The subwoofer output of this unit is monaural.
· When using a subwoofer of 70 W (2 Ω) , be sure to connect with
type. In other types of vehicles,
never connect 6* and 7*.
Violet and Violet/black leads of this unit. Do not connect anything to
Green and Green/black leads.
Connecting the units
When connecting to separately sold power amp
This product
Power amp
(sold separately)
Power amp
(sold separately)
Front output
Connect with RCA cables (sold
Rear output or
separately)
subwoofer output
Blue/white
Connect to system control
terminal of the power amp
(max. 300 mA 12 V DC).
System remote control
Blue/white (7*)
Blue/white (6*)
Connect to auto-antenna
relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 6*
Left
Right
and 7* when Pin 5 is an antenna control type.
In other types of vehicles, never connect 6* and
7*.
When you connect the separately sold
Front speaker
Front speaker
multi-channel processor (e.g., DEQ-P6600) to
this unit, do not connect anything to the
speaker leads and system remote control
(blue/white).
Rear speaker
Rear speaker
or Subwoofer
or Subwoofer
When you connect the multi-channel processor
to this unit, refer to multi-channel processor's
installation manual for the connection method.
Perform these connections when
Note:
using the optional amplifier.
· Change the initial setting of this unit
(refer to the Operation Manual).
The subwoofer output of this unit is monaural.
Connecting the units
Connecting the system
USB cable
Connect to sparately sold
USB device.
1.5 m
This product
20 cm
Multi-CD player
iPod with Dock
(sold separately)
connector
Wired remote input
Gray
Hard-wired remote control
Dock connector
adaptor can be connected
2 m
(sold separately).
Interface cable
(e.g., CD-I200) (sold separately)