Ariston 200D Anweisungen für Installation, Verwendung und Wartung - Seite 2

Blättern Sie online oder laden Sie pdf Anweisungen für Installation, Verwendung und Wartung für Warmwasserbereiter Ariston 200D herunter. Ariston 200D 33 Seiten. Heat pump water heater

Seite drucken

GENERAL SAFETY INSTRUCTIONS

1. Read the instructions and warning in this
manual carefully, they contain important
information regarding safe installation, use
and maintenance. This manual is an integral
part of the product. Hand it on to the next
user/owner in case of change of property.
2. The manufacturer shall not liable for any inju-
ry to people, animals or damage to property
caused by improper, incorrect or unreasona-
ble use or failure to follow the instructions re-
ported in this publication.
3. Installation and maintenance must be per-
formed by professionally qualifi ed personnel
as specifi ed in the relative paragraphs. Only
use original spare parts. Failure to observe
the above instructions can compromise the
safety of the appliance and relieves the man-
ufacturer of any liability for the consequences.
4. DO NOT leave the packaging materials (sta-
ples, plastic bags, expanded polystyrene, etc.)
within the reach of children they can cause
serious injury.
5. The appliance may not be used by persons
under 8 years of age, with reduced physical,
sensory or mental capacity, or lacking the
requisite experience and familiarity, unless
under supervision or following instruction in
the safe use of the appliance and the haz-
ards attendant on such use. DO NOT per-
mit children to play with the appliance. User
cleaning and maintenance may not be done
by unsupervised children.
6. DO NOT touch the appliance when barefoot
or if any part of your body is wet.
7. Before using the device and after routine or
extraordinary maintenance, we recommend fi
lling the appliance's tank with water and drain-
ing it completely to remove any residual impu-
rities.
8. If the appliance is equipped with a power cord,
the latter may only be replaced by an author-
ised service centre or professional technician.
2 /EN
9. It is mandatory to screw o the water inlet pipe
of the unit a safety valve in accordance with
national regulations. In countries which have
enacted EN 1487, the safety group must be
calibrated to a maximum pressure of 0,7 MPa
and include at least a cock, check valve and
control, safety valve and hydraulic load cut-
out.
10. Do not tamper with the overpressure safety
device (valve or safety group), if supplied to-
gether with the appliance; trip it from time to
time to ensure that it is not jammed and to re-
move any scale deposits.
11. It is normal water drips from the overpressure
safety device when the appliance is heating.
For this reason, the drain must be connected,
always left open to the atmosphere, with a
drainage pipe installed in a continuous down-
ward slope and in a place free of ice.
12. Make sure you drain the appliance and dis-
connect it from the power grid when it is out
of service in an area subject to subzero tem-
peratures.
13. Water heated to over 50 °C can cause imme-
diate serious burns if delivered directly to the
taps. Children, disabled persons and the aged
are particularly at risk. We recommend install-
ing a thermostatic mixer valve on the water
delivery line, marked with a red collar.
14. Do not leave fl ammable materials in contact
with or in the vicinity of the appliance.
15. Do not place anything under the water heater
which may be damaged by a leak..
16. The water heating heat pump is supplied with
a sufficient amount of R134a or R513a refrig-
erant for its operation. This refrigerant fluid
does not damage the atmosphere's ozone
layer, is not flammable and does not cause ex-
plosions; however any maintenance activities
or work on the refrigerant circuit must only be
carried out by authorised personnel and with
the use of suitable equipment.