Whirlpool 8182192 Handbuch für Gebrauch und Pflege - Seite 4
Blättern Sie online oder laden Sie pdf Handbuch für Gebrauch und Pflege für Waschmaschine Whirlpool 8182192 herunter. Whirlpool 8182192 44 Seiten. Front-loading automatic washer
Seite druckenINSTALLATION REQUIREMENTS
Assemble the necessary tools and supplies before beginning the
washer installation. The parts supplied are in the washer drum.
Tools needed for connecting
the water inlet hoses
•
Pliers (that open to 1°/16 in. [39.5 mm])
•
Flashlight (optional)
Tools needed
for installation
•
Open end wrench 17 mm and 13 mm
•
Level
•
Wood block (2" x 4")
•
Ruler or measuring tape
Parts supplied:
Pedestal
Are you placing the washer on a pedestal? You may purchase a
pedestal separately for this washer. This pedestal will add about
13 in. (33 cm) to the height of your unit for a total height of
approximately
51 in. (130 cm).
CC>
Beaded strap
Transport bolt hole plug (4)
Alternate
Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free
number on the cover or in the "Assistance
or Service" section.
If You Have
You Will Need to Buy
Laundry tub or
Sump pump system (if not already
standpipe taller
available)
than 96 in. (2.4 m)
Overhead sewer
Standard 20 gal. (76 L), 30 in. (76.2 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain
Siphon break, Part Number 285834;
additional drain hose Part
Number 8318155; and connector
kit,
Part Number 285835
Drain hose too
4 ft drain hose extension kit, Part
short
Number 285863
Water faucets
2 longer water fill hoses:
beyond reach of
6 ft (1.8 m) Part Number 76314,
fill hoses
10 ft (3.0 m) Part Number 350008
Optional pedestal
To order, call the dealer from whom you purchased your washer
or refer to the "Assistance or Service" section of this manual. Ask
for Part Number LAB2700MQ (White), LAB2700MT (Biscuit) or
LAB2700ML (Pewter).
Stack Kit
Are you planning to stack your DUET ° washer and dryer? To do
so you will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance or Service" section of this manual. Ask
for Part Number 8541503.
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer "walk."
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. (See "Drain
System.")
Companion appliance location requirements should also be
considered.
Proper installation is your responsibility.
You will need
•
A water heater set to deliver 120°F (49°C) water to the
washer.
•
A grounded electrical outlet located within 5 ft (1.5 m) of
where the power cord is attached to the back of the washer.
(See "Electrical Requirements.")
•
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6
kPa).
•
A level floor with a maximum slope of 1 in. (2.5 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
•
A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 Ibs (180 kg).
Do not operate your washer in temperatures
below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.