Whirlpool 3395314 Installationsanleitung Handbuch - Seite 3

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Trockner Whirlpool 3395314 herunter. Whirlpool 3395314 12 Seiten. Coin-operated stacked dryer

Seite drucken

Tools needed for

installation:

adjustable wrench

IWSI

utility knife

pliers

Phillips screwdriver

duct tape

flat-blade

screwdriver

Parts supplied for

installation:

2 slide protectors

screws

2 slide extensions

2. 30-minute cams

2 bolt and washer

2,60-minute

cams

assemblies

4,314" wood

screws

Parts owner must

supply:

1 control panel lock and key

2 coin vaults and

keys (E.S.D. vault must

have

projecting

lock.)

2 coin-slide mechanisms (vertical 8)

Parts may be ordered

from

Greenwald

Industries, Inc. or

Equipment

Systems and Devices,

Inc.

Greenwald

Industries, Inc.

1340 Metropolitan

Avenue

Brooklyn, NY 11237

telephone

(7 18) 821-9000 or

toll free (800) 22 l-0982

faxno.

(718)417-7412

Equipment

Systems and

Devices,

Inc.

270

New Jersey Dr.

Fort Washington,

PA 19034

telephone

(215) 628-0860 or

toll free (800) 523- 1510

fax no. (215) 643-4623

Gas supply

requirements

Fire Hazard

These dryers must be connected

to a regulated gas supply.

Failure to do so could result In hlgh-

pressure gas release, resultlng In a

tire or exploslon.

Have L.P. gas checked by a

qualltled person betore lnstalllng

the dryer. The L.P. gas supply must

not exceed a pressure ot 13"

water column.

New tlexlble tublng should be

used. Reuslng old, tlexlble tublng

mlght result In possible leaks or

tire hazard.

Failure to tallow these lnstructlons

could result In tlre or exploslon.

OBSERVE ALL GOVERNING CODES

AND ORDINANCES.

This installation

ust conform

with American

Nationa

Standard,

National

Fuel Gas Cod

ANSI Z223.V

latest edition,

and all lo al codes and

ordinances.

H The design of this dryer has

been certified

by the A

Association

for use at a itudes up to

10,000 feet above

sea I vel at the

B.T.U. rating indicated

n the

adjustments

are not re

elevation.

erican

Gas

model/serial

plate.

Bur

r input

uired when

the dryer is operated

to this

your local service corn

the particular

type o

Burner information

see your dealer.

These drvers are/ shipoed

for

use with NATURAL GAS.

hey are

certified

by the Americ

n Gas

Association

for manufa

tured, mixed

and L.P. (propane

and i utane)

gases

with appropriate

conv&sion.

attempt

shall be made

o convert

the

appliance

from the gas specified

the rating plate for use

ith a

different

gas without

suiting the

serving gas supplier.

verslon must

be done by a qualltled

ervlce

technician.

Gas conver Ion klt part

numbers are llsted on t e gas valve

burner base.

supply line is more than

usage, 3/8-inch,

appro

If local codes and ordinances

permit,

it is recommended

that new

flexible

metal tubing,

design-certified

by the American

Gas Association,

used for connecting

the dryers to the

gas supply line. (The gas feed pipe,

which extends

through

the lower rear

of each

dryer, is provided

with 3/8-

inch male pipe thread.)

shutofl valve

The supplv line shall be

equipped

with a shutoff valve.

This

valve should be located

in the same

room as the dryers and should be in a

location

that allows ease of opening

and closing.

Do Not block access

shutoff valve.

main gas supply line, a

combination

of fittings must be

used to obtain

an in-line connection

to the dryers.

Make sure lower edges,

back

and sides of the cabinet

are free of

obstructions

to permit adequate

clearance

of air openings

for

combustion

air. See 'Recessed

area

and closet installation

instructions"

for

minimum

spacing

requirements,

For ease of installation,

operating

and servicing

(if ever

needed),

adequate

space

should be

provided

around

the dryers.

A l/&inch,

NPT plugged

tapping,

accessible

for test-gauge

connection,

must be installed

immediately

upstream

of the gas

supply connector

to the dryers.

The dryers and their individual

shutoff

valves must be disconnected

from

the gas supply piping

system during

any pressure testing of that system at

test pressures in excess of l/2 psig

(3.4 kPa).

The dryers must be isolated

from the

gas supply piping

system by closing

their individual

manual

shutoff valves

during any pressure testing of the gas

supply piping

system at test pressures

equal

to or less than l/2 psig

(3.4 kPa).

Page 3