Whirlpool 3395314 Інструкція з монтажу Посібник з монтажу - Сторінка 3
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Сушарка Whirlpool 3395314. Whirlpool 3395314 12 сторінок. Coin-operated stacked dryer
Друкувати сторінку
Tools needed for
installation:
adjustable wrench
IWSI
utility knife
pliers
Phillips screwdriver
duct tape
flat-blade
screwdriver
Parts supplied for
installation:
2 slide protectors
8
screws
2 slide extensions
2. 30-minute cams
2 bolt and washer
2,60-minute
cams
assemblies
4,314" wood
screws
Parts owner must
supply:
1 control panel lock and key
2 coin vaults and
keys (E.S.D. vault must
have
projecting
lock.)
2 coin-slide mechanisms (vertical 8)
Parts may be ordered
from
Greenwald
Industries, Inc. or
Equipment
Systems and Devices,
Inc.
l
Greenwald
Industries, Inc.
1340 Metropolitan
Avenue
Brooklyn, NY 11237
telephone
(7 18) 821-9000 or
toll free (800) 22 l-0982
faxno.
(718)417-7412
l
Equipment
Systems and
Devices,
Inc.
270
New Jersey Dr.
Fort Washington,
PA 19034
telephone
(215) 628-0860 or
toll free (800) 523- 1510
fax no. (215) 643-4623
Gas supply
requirements
Fire Hazard
l
These dryers must be connected
to a regulated gas supply.
Failure to do so could result In hlgh-
pressure gas release, resultlng In a
tire or exploslon.
l
Have L.P. gas checked by a
qualltled person betore lnstalllng
the dryer. The L.P. gas supply must
not exceed a pressure ot 13"
water column.
l
New tlexlble tublng should be
used. Reuslng old, tlexlble tublng
mlght result In possible leaks or
tire hazard.
Failure to tallow these lnstructlons
could result In tlre or exploslon.
OBSERVE ALL GOVERNING CODES
AND ORDINANCES.
n
This installation
ust conform
with American
Nationa
Standard,
National
Fuel Gas Cod
ANSI Z223.V
latest edition,
and all lo al codes and
ordinances.
4
B
H The design of this dryer has
been certified
by the A
Association
for use at a itudes up to
10,000 feet above
sea I vel at the
B.T.U. rating indicated
n the
adjustments
are not re
elevation.
i
erican
Gas
model/serial
plate.
Bur
r input
uired when
the dryer is operated
u
to this
your local service corn
the particular
type o
Burner information
wi
see your dealer.
D
n
These drvers are/ shipoed
for
use with NATURAL GAS.
hey are
certified
by the Americ
n Gas
Association
for manufa
tured, mixed
and L.P. (propane
and i utane)
gases
with appropriate
conv&sion.
No
attempt
shall be made
o convert
the
appliance
from the gas specified
on
the rating plate for use
ith a
different
gas without
c
suiting the
serving gas supplier.
Co
verslon must
1
be done by a qualltled
ervlce
technician.
Gas conver Ion klt part
numbers are llsted on t e gas valve
burner base.
supply line is more than
usage, 3/8-inch,
appro
F
n
If local codes and ordinances
permit,
it is recommended
that new
flexible
metal tubing,
design-certified
by the American
Gas Association,
be
used for connecting
the dryers to the
gas supply line. (The gas feed pipe,
which extends
through
the lower rear
of each
dryer, is provided
with 3/8-
inch male pipe thread.)
shutofl valve
G
n
The supplv line shall be
equipped
with a shutoff valve.
This
valve should be located
in the same
room as the dryers and should be in a
location
that allows ease of opening
and closing.
Do Not block access
to
shutoff valve.
main gas supply line, a
combination
of fittings must be
used to obtain
an in-line connection
to the dryers.
n
Make sure lower edges,
back
and sides of the cabinet
are free of
obstructions
to permit adequate
clearance
of air openings
for
combustion
air. See 'Recessed
area
and closet installation
instructions"
for
minimum
spacing
requirements,
J
n
For ease of installation,
operating
and servicing
(if ever
needed),
adequate
space
should be
provided
around
the dryers.
K
n
A l/&inch,
NPT plugged
tapping,
accessible
for test-gauge
connection,
must be installed
immediately
upstream
of the gas
supply connector
to the dryers.
The dryers and their individual
shutoff
valves must be disconnected
from
the gas supply piping
system during
any pressure testing of that system at
test pressures in excess of l/2 psig
(3.4 kPa).
The dryers must be isolated
from the
gas supply piping
system by closing
their individual
manual
shutoff valves
during any pressure testing of the gas
supply piping
system at test pressures
equal
to or less than l/2 psig
(3.4 kPa).
Page 3