Whirlpool CGW9100VQ0 Installationshandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Installationshandbuch für Trockner Whirlpool CGW9100VQ0 herunter. Whirlpool CGW9100VQ0 40 Seiten. Commercial dryer- gas or electric

Seite drucken

iMPORTANT

SAFETY iNSTRUCTiONS

WARNING:

To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[]

Read all instructions

before using the dryer.

[]

Do not place items exposed to cooking

oils in your dryer.

Items contaminated

with cooking

oils may contribute

a chemical reaction that could cause a load to catch fire.

[]

Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry=

cleaning solvents, or other flammable or explosive

substances

as they give off vapors that could ignite or

explode.

[]

Do not allow children to play on or in the dryer. Close

supervision

of children is necessary when the dryer is

used near children.

[]

Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[]

Do not reach into the dryer if the drum is moving.

[]

Do not install or store the dryer where it will be exposed

to the weather.

[]

Do not tamper with controls.

[]

Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended

in this

Use and Care Guide or in published user-repair

instructions

that you understand and have the skills to

carry out.

[]

Do not use fabric softeners or products to eliminate static

unless recommended

by the manufacturer

of the fabric

softener or product.

[]

Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[]

Clean lint screen before or after each load.

[]

Keep area around the exhaust opening and adjacent

surrounding

areas free from the accumulation

of lint, dust,

and dirt.

[]

The interior of the dryer and exhaust vent should be

cleaned periodically

by qualified service personnel.

[]

See installation instructions

for grounding

requirements.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

Tools needed

[]

8" or 10" Pipe wrench

[]

Level

[]

8" or 10" adjustable

[]

1/4"socket and wrench

wrench

[]

Vent clamps

[]

Flat-blade screwdriver

[]

Pipe-joint compound

[]

Phillips screwdriver

resistant to LP gas

[] Adjustable wrench that

[]

Caulk gun and caulk (for

opens to 1" (2.5 cm) or 1"

installing new exhaust

(25 mm) hex-head socket

vent)

wrench

[]

Pliers

[]

Security T-20 TORX_'t

[]

Stiff bladed putty knife

driver

Parts supplied

Remove parts bag from dryer drum. Check that all parts were

included.

[]

Foot boot (4)

[]

Dryer foot (4)

[]

Service door lock cam

Explosion Hazard

Keep flammable

materials and vapors, such as

gasoline,

away from dryer.

Do not install in a garage.

Failure to do so can result in death, explosion,

or fire.

If installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

[]

Check code requirements: Some codes limit or do not permit

installation of clothes dryers in garages, closets, or sleeping

quarters. Contact your local building inspector.

[]

Make sure that lower edges of the cabinet, plus the back and

bottom sides of the dryer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

"Recessed Area and Closet Installation Instructions" below

for minimum spacing requirements.

NOTE: The dryer must not be installed in an area where it will

be exposed to water and/or weather.

1 ® TORX is a registered

trademark

of Acument

Intellectual

Properties,

LLC.