Whirlpool CGW9100VQ0 Kurulum Kılavuzu - Sayfa 4

Kurutucu Whirlpool CGW9100VQ0 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Whirlpool CGW9100VQ0 40 sayfaları. Commercial dryer- gas or electric

Sayfayı Yazdır
iMPORTANT
SAFETY iNSTRUCTiONS
WARNING:
To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
[]
Read all instructions
before using the dryer.
[]
Do not place items exposed to cooking
oils in your dryer.
Items contaminated
with cooking
oils may contribute
to
a chemical reaction that could cause a load to catch fire.
[]
Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry=
cleaning solvents, or other flammable or explosive
substances
as they give off vapors that could ignite or
explode.
[]
Do not allow children to play on or in the dryer. Close
supervision
of children is necessary when the dryer is
used near children.
[]
Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
[]
Do not reach into the dryer if the drum is moving.
[]
Do not install or store the dryer where it will be exposed
to the weather.
[]
Do not tamper with controls.
[]
Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended
in this
Use and Care Guide or in published user-repair
instructions
that you understand and have the skills to
carry out.
[]
Do not use fabric softeners or products to eliminate static
unless recommended
by the manufacturer
of the fabric
softener or product.
[]
Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[]
Clean lint screen before or after each load.
[]
Keep area around the exhaust opening and adjacent
surrounding
areas free from the accumulation
of lint, dust,
and dirt.
[]
The interior of the dryer and exhaust vent should be
cleaned periodically
by qualified service personnel.
[]
See installation instructions
for grounding
requirements.
SAVE THESE INSTRUCTIONS
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools needed
[]
8" or 10" Pipe wrench
[]
Level
[]
8" or 10" adjustable
[]
1/4"socket and wrench
wrench
[]
Vent clamps
[]
Flat-blade screwdriver
[]
Pipe-joint compound
[]
Phillips screwdriver
resistant to LP gas
[] Adjustable wrench that
[]
Caulk gun and caulk (for
opens to 1" (2.5 cm) or 1"
installing new exhaust
(25 mm) hex-head socket
vent)
wrench
[]
Pliers
[]
Security T-20 TORX_'t
[]
Stiff bladed putty knife
driver
Parts supplied
Remove parts bag from dryer drum. Check that all parts were
included.
[]
Foot boot (4)
[]
Dryer foot (4)
[]
Service door lock cam
Explosion Hazard
Keep flammable
materials and vapors, such as
gasoline,
away from dryer.
Do not install in a garage.
Failure to do so can result in death, explosion,
or fire.
If installing a gas dryer:
IMPORTANT: Observe all governing codes and ordinances.
[]
Check code requirements: Some codes limit or do not permit
installation of clothes dryers in garages, closets, or sleeping
quarters. Contact your local building inspector.
[]
Make sure that lower edges of the cabinet, plus the back and
bottom sides of the dryer, are free of obstructions to permit
adequate clearance of air openings for combustion air. See
"Recessed Area and Closet Installation Instructions" below
for minimum spacing requirements.
NOTE: The dryer must not be installed in an area where it will
be exposed to water and/or weather.
1 ® TORX is a registered
trademark
of Acument
Intellectual
Properties,
LLC.
4