Yamaha S03 voice editor Datenliste - Seite 20

Blättern Sie online oder laden Sie pdf Datenliste für Musikinstrument Yamaha S03 voice editor herunter. Yamaha S03 voice editor 29 Seiten. Voice editor
Auch für Yamaha S03 voice editor: Datenliste (28 seiten), Software-Installationshandbuch (20 seiten), Benutzerhandbuch (26 seiten)

Yamaha S03 voice editor Datenliste
1.2.16 Portamento Control
This message specifies the portamento source key number (the key number at which
portamento will begin).
Data of 0...127 specifies the portamento source key.
When Portamento Control is received, the currently-sounding pitch will change at a
Portamento Time of 0 to the key of the next-received note-on of the same channel.
Control#
Parameter
84
Portamento Control
This is received even if Rcv PORTAMENTO = OFF.
1.2.17 Effect1 Depth (Reverb Send Level)
This message specifies the send level for the reverb effect.
Control#
Parameter
91
Effect1 Depth
Increasing this value will produce a richer reverb. The effect of the value will depend on the
state of the reverb effect.
1.2.18 Effect3 Depth (Chorus Send Level)
This message specifies the send level for the chorus effect.
Control#
Parameter
93
Effect3 Depth
Raising this value will increase the modulation or spaciousness. The effect of the value will
depend on the state of the chorus effect.
1.2.19 Effect4 Depth (Variation Effect Send Level)
This message specifies the send level for the variation effect.
Control#
Parameter
94
Effect4 Depth
However, this is not received if the Variation Effect parameter Variation Connection = 0
(Insertion).
1.2.20 Data Increment/Decrement (for RPN)
This message increases or decreases the parameter value specified for RPN (see 1.2.22),
by increments of 1.
Control#
Parameter
96
RPN Increment
97
RPN Decrement
The data byte is ignored.
1.2.21 NRPN (Non-registered parameter number)
This message is used to specify a sound parameter (such as vibrato, filter, EG, drum setup
etc.) as an offset value.
Use NRPN MSB and NRPN LSB to specify the parameter that you wish to modify, and
then use Data Entry (see 1.2.4) to set the value for the specified parameter.
Control#
Parameter
98
NRPN LSB
99
NRPN MSB
If the Multi Part parameter Rcv NRPN = OFF, that part will not receive NRPN.
The following NRPN messages can be received.
*1
NRPN
Data Entry
MSB LSB
MSB LSB
Parameter name and value range
*2
01H 08H
mm
--
Vibrato rate
mm : 00H - 40H - 7FH (-64...0...+63)
01H 09H
mm
--
Vibrato depth
mm : 00H - 40H - 7FH (-64...0...+63)
*3
01H 0AH
mm
--
Vibrato delay
mm : 00H - 40H - 7FH (-64...0...+63)
01H 20H
mm
--
Low pass filter cutoff frequency
mm : 00H - 40H - 7FH (-64...0...+63)
01H 21H
mm
--
Low pass filter resonance
mm : 00H - 40H - 7FH (-64...0...+63)
01H 63H
mm
--
EG attack time
mm : 00H - 40H - 7FH (-64...0...+63)
01H 64H
mm
--
EG decay time
mm : 00H - 40H - 7FH (-64...0...+63)
01H 66H
mm
--
EG release time
mm : 00H - 40H - 7FH (-64...0...+63)
14H rr
mm
--
Drum low pass filter cutoff frequency
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
15H rr
mm
--
Drum low pass filter resonance
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
16H rr
mm
--
Drum EG attack rate
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
17H rr
mm
--
Drum EG decay rate
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
The effect will apply both to Decay 1 and 2.
18H rr
mm
--
Drum instrument pitch coarse
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
Data Range
0...127
(C-2...G8)
Data Range
0...127
Data Range
0...127
Data Range
0...127
Data Range
--
--
Data Range
0...127
0...127
*1
NRPN
Data Entry
MSB LSB
MSB LSB
Parameter name and value range
19H rr
mm
--
Drum instrument pitch fine
1AH rr
mm
--
Drum instrument level
1CH rr
mm
--
Drum instrument panpot
1DH rr
mm
--
Drum instrument reverb send level
1EH rr
mm
--
Drum instrument chorus send level
1FH rr
mm
--
Drum instrument variation send level
MSB 14H - 1FH (for drums) is received when Multi Part parameter PART MODE =
DRUMS1, 2.
*1
Refer to 1.2.4
*2
'--' indicates that the setting value is ignored.
*3
Adjusts the time after the note is played until vibrato begins to take effect. The effect
will begin more quickly for higher values, and more slowly for higher values.
1.2.22 RPN (Registered parameter number)
This message is used to specify part parameters such as Pitch Bend Sensitivity or Tuning
etc. as an offset value.
Use RPN MSB and RPN LSB to specify the parameter that you wish to modify, and then
use Data Entry (see 1.2.4) to set the value of the specified parameter.
Control#
Parameter
100
RPN LSB
101
RPN MSB
If the Multi Part parameter Rcv RPN = OFF, that part will not receive this message.
The following RPN messages can be received.
*1
NRPN
Data Entry
MSB LSB
MSB LSB
Parameter name and value range
*2
00H 00H
mm
--
Pitch bend sensitivity
00H 01H
mm
ll
Fine tuning
00H 02H
mm
--
Coarse tuning
7FH 7FH
--
--
RPN Null
*1
Refer to 1.2.4
*2
'--' indicates that the setting value is ignored.
1.2.23 Assignable controller
By assigning a control change number of 0...95 to a part, the specified effect can be
controlled.
This device allows two control change numbers (AC1 and AC2) to be specified for each
part.
The following parameters specify the effect of AC1 and AC2.
• Multi Part Parameter
1. AC1, AC2 PITCH CONTROL
2. AC1, AC2 FILTER CONTROL
3. AC1, AC2 AMPLITUDE CONTROL
4. AC1, AC2 LFO PMOD DEPTH
5. AC1, AC2 LFO FMOD DEPTH
6. AC1, AC2 LFO AMOD DEPTH
• Effect1 Parameter
7. AC1, AC2 VARIATION CONTROL DEPTH
(Valid if Variation Effect is assigned to a part as Insertion)
The AC1 control change number is specified by the Multi Part parameter AC1
CONTROLLER NUMBER, and the AC2 control change number is specified by the Multi
Part parameter AC2 CONTROLLER NUMBER.
19
rr : drum instrument note number
mm : 00H - 40H - 7FH (-64...0...+63)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
rr : drum instrument note number
mm : 00H, 01H-40H-7FH (RND, L63...C...R63)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
rr : drum instrument note number
mm : 00H - 7FH (0...maximum)
(when Variation Connection = SYSTEM)
mm : 00H, 01H-7FH (OFF, ON)
(when Variation Connection = INSERTION)
Data Range
0...127
0...127
mm:00-18H (0...+24 semitones)
Specify up to 2 octaves in semitone steps\
mm ll: 00H 00H
-100 cents
:
:
mm ll: 40H 00H
0 cents
:
:
mm ll: 7FH 7FH
+100 cents
[Note] mm ll: 00H 7FH (= -87.5) cents is followed by 01H
00H (= -87.4) cents.
mm:28H - 40H - 58H (-24...0...+24 semitones)
This sets RPN and NRPN numbers to an unset state.
Internal data is not affected.