Yamaha S03 voice editor Veri Listesi - Sayfa 20

Müzik Enstrümanı Yamaha S03 voice editor için çevrimiçi göz atın veya pdf Veri Listesi indirin. Yamaha S03 voice editor 29 sayfaları. Voice editor
Ayrıca Yamaha S03 voice editor için: Veri Listesi (28 sayfalar), Yazılım Kurulum Kılavuzu (20 sayfalar), Kullanıcı El Kitabı (26 sayfalar)

Sayfayı Yazdır

1.2.16 Portamento Control

This message specifies the portamento source key number (the key number at which

portamento will begin).

Data of 0...127 specifies the portamento source key.

When Portamento Control is received, the currently-sounding pitch will change at a

Portamento Time of 0 to the key of the next-received note-on of the same channel.

Control#

Parameter

Portamento Control

This is received even if Rcv PORTAMENTO = OFF.

1.2.17 Effect1 Depth (Reverb Send Level)

This message specifies the send level for the reverb effect.

Control#

Parameter

Effect1 Depth

Increasing this value will produce a richer reverb. The effect of the value will depend on the

state of the reverb effect.

1.2.18 Effect3 Depth (Chorus Send Level)

This message specifies the send level for the chorus effect.

Control#

Parameter

Effect3 Depth

Raising this value will increase the modulation or spaciousness. The effect of the value will

depend on the state of the chorus effect.

1.2.19 Effect4 Depth (Variation Effect Send Level)

This message specifies the send level for the variation effect.

Control#

Parameter

Effect4 Depth

However, this is not received if the Variation Effect parameter Variation Connection = 0

(Insertion).

1.2.20 Data Increment/Decrement (for RPN)

This message increases or decreases the parameter value specified for RPN (see 1.2.22),

by increments of 1.

Control#

Parameter

RPN Increment

RPN Decrement

The data byte is ignored.

1.2.21 NRPN (Non-registered parameter number)

This message is used to specify a sound parameter (such as vibrato, filter, EG, drum setup

etc.) as an offset value.

Use NRPN MSB and NRPN LSB to specify the parameter that you wish to modify, and

then use Data Entry (see 1.2.4) to set the value for the specified parameter.

Control#

Parameter

NRPN LSB

NRPN MSB

If the Multi Part parameter Rcv NRPN = OFF, that part will not receive NRPN.

The following NRPN messages can be received.

NRPN

Data Entry

MSB LSB

Parameter name and value range

01H 08H

Vibrato rate

mm : 00H - 40H - 7FH (-64...0...+63)

01H 09H

Vibrato depth

mm : 00H - 40H - 7FH (-64...0...+63)

01H 0AH

Vibrato delay

mm : 00H - 40H - 7FH (-64...0...+63)

01H 20H

Low pass filter cutoff frequency

mm : 00H - 40H - 7FH (-64...0...+63)

01H 21H

Low pass filter resonance

mm : 00H - 40H - 7FH (-64...0...+63)

01H 63H

EG attack time

mm : 00H - 40H - 7FH (-64...0...+63)

01H 64H

EG decay time

mm : 00H - 40H - 7FH (-64...0...+63)

01H 66H

EG release time

mm : 00H - 40H - 7FH (-64...0...+63)

14H rr

Drum low pass filter cutoff frequency

rr : drum instrument note number

mm : 00H - 40H - 7FH (-64...0...+63)

15H rr

Drum low pass filter resonance

rr : drum instrument note number

mm : 00H - 40H - 7FH (-64...0...+63)

16H rr

Drum EG attack rate

rr : drum instrument note number

mm : 00H - 40H - 7FH (-64...0...+63)

17H rr

Drum EG decay rate

rr : drum instrument note number

mm : 00H - 40H - 7FH (-64...0...+63)

The effect will apply both to Decay 1 and 2.

18H rr

Drum instrument pitch coarse

rr : drum instrument note number

mm : 00H - 40H - 7FH (-64...0...+63)

Data Range

0...127

(C-2...G8)

Data Range

0...127

Data Range

0...127

Data Range

0...127

Data Range

0...127

NRPN

Data Entry

MSB LSB

Parameter name and value range

19H rr

Drum instrument pitch fine

1AH rr

Drum instrument level

1CH rr

Drum instrument panpot

1DH rr

Drum instrument reverb send level

1EH rr

Drum instrument chorus send level

1FH rr

Drum instrument variation send level

MSB 14H - 1FH (for drums) is received when Multi Part parameter PART MODE =

DRUMS1, 2.

Refer to 1.2.4

'--' indicates that the setting value is ignored.

Adjusts the time after the note is played until vibrato begins to take effect. The effect

will begin more quickly for higher values, and more slowly for higher values.

1.2.22 RPN (Registered parameter number)

This message is used to specify part parameters such as Pitch Bend Sensitivity or Tuning

etc. as an offset value.

Use RPN MSB and RPN LSB to specify the parameter that you wish to modify, and then

use Data Entry (see 1.2.4) to set the value of the specified parameter.

Control#

Parameter

100

RPN LSB

101

RPN MSB

If the Multi Part parameter Rcv RPN = OFF, that part will not receive this message.

The following RPN messages can be received.

NRPN

Data Entry

MSB LSB

Parameter name and value range

00H 00H

Pitch bend sensitivity

00H 01H

Fine tuning

00H 02H

Coarse tuning

7FH 7FH

RPN Null

Refer to 1.2.4

'--' indicates that the setting value is ignored.

1.2.23 Assignable controller

By assigning a control change number of 0...95 to a part, the specified effect can be

controlled.

This device allows two control change numbers (AC1 and AC2) to be specified for each

part.

The following parameters specify the effect of AC1 and AC2.

• Multi Part Parameter

1. AC1, AC2 PITCH CONTROL

2. AC1, AC2 FILTER CONTROL

3. AC1, AC2 AMPLITUDE CONTROL

4. AC1, AC2 LFO PMOD DEPTH

5. AC1, AC2 LFO FMOD DEPTH

6. AC1, AC2 LFO AMOD DEPTH

• Effect1 Parameter

7. AC1, AC2 VARIATION CONTROL DEPTH

(Valid if Variation Effect is assigned to a part as Insertion)

The AC1 control change number is specified by the Multi Part parameter AC1

CONTROLLER NUMBER, and the AC2 control change number is specified by the Multi

Part parameter AC2 CONTROLLER NUMBER.

rr : drum instrument note number

mm : 00H - 40H - 7FH (-64...0...+63)

rr : drum instrument note number

mm : 00H - 7FH (0...maximum)

rr : drum instrument note number

mm : 00H, 01H-40H-7FH (RND, L63...C...R63)

rr : drum instrument note number

mm : 00H - 7FH (0...maximum)

rr : drum instrument note number

mm : 00H - 7FH (0...maximum)

rr : drum instrument note number

mm : 00H - 7FH (0...maximum)

(when Variation Connection = SYSTEM)

mm : 00H, 01H-7FH (OFF, ON)

(when Variation Connection = INSERTION)

Data Range

0...127

mm:00-18H (0...+24 semitones)

Specify up to 2 octaves in semitone steps\

mm ll: 00H 00H

-100 cents

mm ll: 40H 00H

0 cents

mm ll: 7FH 7FH

+100 cents

[Note] mm ll: 00H 7FH (= -87.5) cents is followed by 01H

00H (= -87.4) cents.

mm:28H - 40H - 58H (-24...0...+24 semitones)

This sets RPN and NRPN numbers to an unset state.

Internal data is not affected.