Directed Xpresskit DBALL2 Installationshandbuch - Seite 8

Blättern Sie online oder laden Sie pdf Installationshandbuch für Durch Schlösser Directed Xpresskit DBALL2 herunter. Directed Xpresskit DBALL2 12 Seiten. Ford5 remote start ready (rsr) installation
Auch für Directed Xpresskit DBALL2: Installationshandbuch (19 seiten), Installationshandbuch (18 seiten), Handbuch (14 seiten), Installationshandbuch (13 seiten), Installationshandbuch (14 seiten), Installationshandbuch (19 seiten), Installationshandbuch (16 seiten), Installationshandbuch (20 seiten), Installationshandbuch (15 seiten), Handbuch für Installation und Kurzanleitung (16 seiten), Installationshandbuch (18 seiten), Installationshandbuch (16 seiten), Installationshandbuch (18 seiten), Installationshandbuch (16 seiten), Handbuch (19 seiten)

Seite drucken

Directed Xpresskit DBALL2 Installationshandbuch

Platform: DBALL2

Firmware: MIT2

LED Diagnostics & Troubleshooting

LED

Description

Module Programming

Off

Module has no power.

Waiting to begin the programming sequence.

Solid red

Initialization failed.

Flashes red

& green

Solid orange

Transponder functions were skipped.

Flashes

All required CAN networks has been detected.

green

Flashes

1 of 2 CAN networks has been detected.

orange

Flashes

Key2GO initiated.

orange

slowly

Solid green

Module was successfully programmed with all functions. Normal operation

x 3 secs

Module was successfully programmed without

Solid orange

x 3 secs

transponder functions.

Module Programming - Error Codes

Flashes red

CAN2 not detected.

x 1

Flashes red

J1850 not detected.

x 1

Flashes red

CAN1 not detected.

x 2

Flashes red

Bypass data not detected.

x 3

Flashes red

Bypass processing error.

x 4

Flashes red

ISO 1 not detected.

x 5

Flashes red

ISO 2 not detected.

x 6

Flashes red

MUX not detected.

x 7

Troubleshooting

Make sure the D2D harness is connected or that the 12

Volt is present between the red and black wires. If the

12 Volt is present, the module may be defective.

Ensure the correct programming procedure is being

followed.

Reset the module and complete the programming again.

If the issue persists, please contact Technical Support.

(If compatible) when RXT mode is not desired or

convenience features are needed, please reset and

reprogram the module.

Normal operation.

Normal operation

Please follow the steps indicated in "Module

programming" to complete the Key2GO programming.

Normal operation.

Check the CAN2 Orange/Green and Orange/Brown wire

connections. Wake up the data bus by turning the

ignition on and try again. If your installation does not

require this connection, skip this step by pressing the

programming button 5 times.

Check the J1850 wire connection. Wake up the data bus

by turning the ignition on and try again.

Check the CAN1 Tan and Tan/Black wire connections.

Wake up the data bus by turning the ignition on and try

again. If your installation does not require this

connection, skip this step by pressing the programming

button 5 times.

Check the bypass line connection. If more than one wire

is used, make sure they are not inverted. Ensure the

vehicle still operates correctly using the factory key.

The bypass calculation failed. Reset the module and try

again. If the condition persists, please contact Technical

Support.

The Yellow/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

The Orange/Black wire did not detect the expected

signal. Refer to "Installation (wiring diagrams & vehicle

wiring reference charts)" to check the connections.

The Violet/Green or Violet/Brown wire did not detect the

expected voltage value. Refer to "Installation (wiring

diagrams & vehicle wiring reference charts)" to check

the connections.

Rev.: 20170620

Page 8