ARNOLD 490-241-0009 Handbuch

Blättern Sie online oder laden Sie pdf Handbuch für Beleuchtungsanlagen ARNOLD 490-241-0009 herunter. ARNOLD 490-241-0009 2 Seiten. Snow thrower accessories

Seite drucken

490-241-0009

SNOW THROWER LIGHT

FITS 179cc, 208cc, 277cc, 357cc and 420cc MTD AND CRAFTSMAN BRANDED SNOW

THROWER ENGINES WITH ALTERNATORS, AND ALL TECUMSEH AND BRIGGS & STRATTON

SNOW THROWER ENGINES WITH ALTERNATORS.

Contents of Package

Part Numbers shown in parentheses

10mm Bolt (1)

Star Handled Bolt (1)

710-1313

710-04862*

Nylon Washers (2)

Zip Ties (2)

750-05236*

926-0240

725-04913 †

725-1629 †

Light Housing Assembly (1)

925-04848

* Available as part of Hardware Pack 753-05959

† Part of Light Housing Assembly 925-04848

Adjustments

The angle of the light can be changed by tilting the light housing assembly forward or backward

and left or right, or by moving the L-bracket up and down.

If the vibration causes the light kit to move or become loose on the handle, add extra pieces of

rubber between the snow thrower handle and the hinged clamp to absorb the vibration.

If the wires from the light do not reach their connection points, a small cut in the casing around

the wires allows the casing to be pulled apart, freeing up more wire length.

Rubber Shim, 3/4" long

Rubber Shim, 3-3/4" long

735-04166*

735-04167*

Lock Washers (2)

Steel "L" Bracket (1)

936-0171

790-00350*

Adapter Wire**

2-Piece Hinged Clamp (1)

925-04872

790-00354* & 790-00355*

** (For use with snow throwers equipped

with Tecumseh or Briggs & Stratton engine)

Installation

The Light Kit can be mounted on the crossbar of the lower handle or either the upper right or left handle.

NOTE: Be sure that the location you choose allows you enough wiring to reach the alternator plugs on the engine and that the light kit does not

interfere with the operation of the snow thrower.

Rubber Shim

Determine which location on the handle tube works

best for you. Put the 3/4" rubber shim there, then

place the hinged clamp over it, making sure the

hinges are over the rubber shim. (Push hinges

together with fingers, or pliers if necessary.)

NOTE: If you have a 7⁄ 8" handle you will need to wrap

the rubber shim (3-3/4" long) around the handle first

to ensure a proper fit.

Wind the two covered wires around the lower

handle and down to the alternator plugs on the

engine. Secure them with zip ties.

NOTE: On some models, you may have to pivot the

snow thrower forward and reach between the front

of the engine and the auger housing to access the

alternator plug. On single-stage models, it is easiest

to remove the belt cover to access the alternator

plug. Refer to your Operator's Manual for instructions.

Lock Washer

Nylon Washer

Mount the "L" bracket and secure the hinged

clamp with a nylon washer, lock washer and

the 10mm bolt.

Adaptor

Wire

Light Wire

Remove the cap/plug from the alternator socket

(if present) and plug the light wire into the

alternator socket.

NOTE: If your snow thrower is equipped with a

Tecumseh or Briggs & Stratton engine that uses a

single line adapter wire, install the adaptor wire on

the end of the light wire then plug the adapter wire

into the alternator plug. See Fig. 5

Nylon Washer

Lock Washer

Mount the light housing assembly to the "L" bracket

using a nylon washer, lock washer and the star

handled bolt.

Ground Wire

Engine Screw

Secure the ground wire to a bolt located on

the engine. Select a bolt that is not securing a

gasket.

NOTE: If the ground wire cannot not reach an engine

screw, a small cut in the casing around the wires

allows the casing to be pulled apart, freeing up more

wire length.