Altronix HubSat42D Installationshandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Installationshandbuch für Schalter Altronix HubSat42D herunter. Altronix HubSat42D 8 Seiten. Passive utp transceiver hub with integral camera power

Seite drucken

3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5a, pg. 6) power

LEDs (Green) of the HubSat will illuminate when AC power is present (Fig. 1e, pg. 4) and HubWayAv, HubWayDv

or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).

4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to

each camera to insure proper operation and avoid possible damage.

5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5a, pg. 6).

6. Connect power outputs of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to power

inputs of cameras (Figs. 2a-2e, pg. 5-6). Polarity must be observed.

•

HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 5-6).

•

HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 5).

7. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video

Balun/Combiners to data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 5). Polarity must be observed.

When using fixed cameras disregard this step.

8. Connect the BNC connector of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to

the BNC video outputs of cameras (Figs. 2a-2e, pg. 5-6).

9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5a, pg. 6).

10. The power LEDs (Green) of the HubSat will illuminate when AC power is present (Fig. 1e, pg. 4).

Note: If any of the power LEDs are not illuminated the cause may be due to the following:

a. AC mains fail.

b. Illuminated master power disconnect circuit breaker is tripped.

c. One or both primary in-line fuse(s) are blown.

Note: Replace fuse with same type and rating:

Primary in-line fuses are rated @ 3.5A/250V (Fig. 5b, pg. 6).

d. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 4).

e. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.

To reset the PTC:

Fig. 1 - HubSat Circuit Board

VIDEO1

1a - BNC Connector: Video in from remote camera

video out to DVR.

1b - Output PTCs: Protects each output.

1c - Power Terminals: 24VAC/28VAC power outputs.

1d - Output Voltage Switches: Selects 24VAC/28VAC/

OFF for each output.

1e - LED(s) 1-4: Power output indicators.

1f - Data: RS422/RS485 input from head end equipment

(DVR) for PTZ control.

- 4 -

28VAC

AUX1

AUX2

24VAC

PVD1

PVD2

28VAC

24VAC

VIDEO2

VIDEO3

DATA 1-4

VIDEO 1-4

1g - Channels 1-4: Single CAT-5 or higher structured

cable out to HubWay, HubWayLD or HubWayLDH

enables transmission of up to four (4) video signals.

Pin out configuration (Fig. 4, pg. 6).

1h - Data: CAT-5 or higher structured cable to data port

on HubWay, HubWayLD or HubWayLDH or head end

equipment (DVR).

1i - Channels 1-4: CAT-5 or higher structured cable

to cameras. Pin out configuration (Fig. 3, pg. 6).

Primary

In-line Fuse

28VAC

AUX3

AUX4

24VAC

VIDEO4

PVD3

PVD4

HubSat4D