Altronix HubSat42D Installationshandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Installationshandbuch für Schalter Altronix HubSat42D herunter. Altronix HubSat42D 8 Seiten. Passive utp transceiver hub with integral camera power

Seite drucken
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must
remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig. 1d, pg. 4).
2. Eliminate the trouble condition (short circuit or overload).
3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 4).
Alternate 24VAC fixed camera hookup (Fig. 6a, pg. 7).
After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay, HubWayLD or
HubWayLDH UTP Transceiver Hubs proceed with the following.
1. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5a, pg. 6).
2. Connect one end of the coaxial cable to the BNC connector marked [Video1] on HubSat (Fig. 1a, pg. 4).
Connect the opposite end of the coaxial cable to the BNC video output of camera 1 (Fig. 7a, pg. 7).
3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5a, pg. 6) measure the
output voltage at terminal pair marked [AUX1] on HubSat to insure proper operation and avoid possible
damage (Fig. 1b, pg. 4).
4. Connect the power output terminal pair marked [AUX1] on HubSat to the power inputs of camera 1
(Fig. 1c, pg. 4). Repeat steps 1-3 for each additional camera [AUX2-4].

HubWayAv, HubWayAv2, HubWayDv, and HubWayDvi Video Balun/Combiners:

Input Voltage
Altronix
from HubWay
Model Number
HubWayAv
*24VAC/28VAC
HubWayAv2
*24VAC/28VAC
HubWayDv
*24VAC/28VAC
HubWayDvi
*24VAC/28VAC
*Based on camera load and structured cable length.
Fig. 2 - HubWayAv and HubWayDv/Dvi Video Balun/Combiners
Fig. 2a
VIDEO
VIDEO BALUN/COMBINER
CAT5
RJ45 Jack
Fig. 2b
To BNC
Structured
Connector
Cable from
of Camera
HubSat4D
HubWayAv passes AC voltage from pins
4, 5, 7, 8 to terminals marked [AC Power]
(Fig. 3, pg. 6).
Fig. 2e
HubWayAv2
Cat5
back to
HubWay
or
HubSat
HubSat4D
Unit
Output Voltage to Camera
*24VAC/28VAC
*24VAC/28VAC
12VDC
12VDC electronically isolated 12VDC cameras without isolation Red
HubWayAv
AC
+ DATA-- POWER
Wire Connectors
Green
Power LED
+
--
AC Power
Data to
to Camera
Camera
Camera Type
*24VAC/28VAC
*24VAC/28VAC
12VDC cameras
Fig. 2c
VIDEO
VIDEO BALUN/COMBINER
RJ45 Jack
Fig. 2d
Structured
To BNC
Cable from
Connector
HubSat4D
of Camera
HubWayDv/HubWayDvi converts AC voltage to DC
voltage from pins 4, 5, 7, 8 to terminals marked
[-- 12VDC +] (Fig. 3, pg. 6).
Power to Camera
HubWayAv2 passes AC voltage from pins
4, 5, 7, 8 to terminals marked [AC Power]
Data to Camera
(Fig. 3, pg. 6).
Video from Camera
Power LED
Green
N/A
Red
* Also Available as:
HubWayDvi
Video Balun/
HubWayDv
Combiner
for non-isolated
12VDC cameras
CAT5
+ DATA-- -- 12VDC+
Wire Connectors
Red
Power LED
+
--
+
12VDC Power
Data to
--
to Camera
Camera
- 5 -