ALUZ ZIBI A1 Series Handbuch - Seite 12

Blättern Sie online oder laden Sie pdf Handbuch für Beleuchtungsanlagen ALUZ ZIBI A1 Series herunter. ALUZ ZIBI A1 Series 13 Seiten. Surface zuco pivot bios illuminated
Auch für ALUZ ZIBI A1 Series: Installationsanleitung Handbuch (12 seiten), Handbuch (11 seiten), Handbuch (11 seiten), Installationsanleitung Handbuch (11 seiten)

Seite drucken

TROUBLESHOOTING TIPS

• Do not reset the breaker multiple times.

• If the unit is overloaded, the breaker will trip, shutting off the driver

and lights.

• If the breaker reset button has been held down by hand or any type of

pressure, such as duct tape, or if the breaker has been reset multiple

times without troubleshooting, the unit will:

- Burn the driver bobbin.

- Burn the thermal or magnetic breaker.

- Burn the driver lead wires due to high amperage caused by overload.

- Short circuit in line which will not allow the breaker to reset.

- Damage the lighting.

Turn off power before beginning. Check for any twisting or damage

to the circuit in the LED lightstrip. If there is excessive damage and

the circuit is broken, the lightstrip must be replaced.

Check for metal particles or other foreign objects causing the short.

Check to make sure cuts in the lightstrip are clean and not frayed,

causing positive and negative copper pads to touch.

CONTINUITY TEST

A continuity test is performed to determine if electricity can pass

through two points on an electrical circuit. This helps identify shorts

or malfunctions in the luminaire. Use a multimeter or continuity

tester to perform the steps below.

• Always perform a continuity test before connecting to power source.

• Malfunctions are not always as obvious as the lights not turning on.

• A short or malfunction in the line or luminaire will cause damage over

time, irreparably damaging the lighting and voiding warranty.

Turn off power before beginning. Verify power is off by using a non-

contact circuit tester (by others). Touch the probe of the tester to

the positive wire of the power source. The tester will light up if an

electrical current is detected.

Setup your multimeter tester (by others). First, insert the black

probe lead into the COM jack, then insert the red probe lead into

the VΩ jack.

1170 N Red Gum St, Anaheim, CA 92806

aluz.lighting

[email protected]

A1 Series | Surface

ZIBI Standard Dynamic White

(A1-ZIBI-STN-DWH)

866.ALUZ.LTG | 714.535.7900

Touch the red probe to the luminaire extrusion and the black probe

to the ground wire (green). If the luminaire is properly grounded,

the multimeter will beep, flash, or read 0Ω (ohms). If there is no

conductive path, the multimeter will not show any feedback.

Troubleshoot to identify the malfunction in the ground wire.

(

Touch the red probe to any wire and the black probe to each other

wire. Repeat process for each wire. If a conductive path is formed

between any of the wires, the multimeter will beep, flash, or read

0Ω (ohms). Troubleshoot to identify the malfunction in the line.

If there is no conductive path, the multimeter will not show any

feedback.

Example: Check for continuity between Wire 2 and Wire 4

(

Touch the red probe to the luminaire housing and the black probe

to each wire except ground. If a conductive path is formed between

the housing and any of the wires, the multimeter will beep, flash,

or read 0Ω (ohms). Troubleshoot to identify the malfunction in the

line. If there is no conductive path, the multimeter will not show

any feedback.

(

Set multimeter to AC voltage and test power source. Conﬁ rm the

correct voltage before connecting luminaire to power source. If the

voltage reading is more than 1 volt greater than the marked output

voltage, there is a problem with the power source or driver.

Connect luminaire to power source. If LEDs do not turn on,

troubleshoot to ﬁ nd the problem in the line.

Page 12 of 13

Troubleshooting & Continuity Test

)

Installation Instructions

9 / 11 / 2023 / Rev 4