Euro-Pro BIG SHARK V1505 Manual del usuario - Página 4
Navegue en línea o descargue pdf Manual del usuario para Aspiradora Euro-Pro BIG SHARK V1505. Euro-Pro BIG SHARK V1505 4 páginas. 120v., 60hz., 7.5 amps
OPERATING INSTRUCTIONS
Warning:
Always unplug from
electrical outlet before opening the dust
cup (container).
Note
: HEPA dust cup filter must be
used when operating the hand vacuum.
Using The Unit As A Hand
Vacuum
1. To open the dust cup (container), push
the dust cup release button and pull
out the dust cup. Verify that the HEPA
dust cup filter is inside, then re-attach
the dust cup (container) to the hand
vacuum.
2. To use the Hand Vacuum
with the shoulder strap,
attach it to the unit as
shown below.
3. To attach the crevice tool or oval
brush to the Hand Vacuum, push
brush into the suction hole, as
shown below.
4. To use the flexible hose, push the
smaller end of the hose into the
suction hole, then attach the desired
accessory to the other end of the
flexible hose, as shown below.
How To Operate Your
Hand Vacuum
1. Hold the hand vacuum firmly in
your hand by the Handle.
2. Push the On/Off Power Switch to
"On" position.
3. Start vacuuming.
CAUTION:
The Hand Vacuum is a
very powerful unit. Make sure that you
hold it firmly, otherwise it can slip out of
your hand and cause injury.
Intelli-Sense
TM
Filter Monitor
When the Intelli-Sense
TM
Filter
Monitor lights up, it means that the
dust cup is full or filter needs
cleaning. You must empty the dust
from the dust cup and clean the
HEPA dust cup filter right away.
3
OPERATING INSTRUCTIONS cont.
Cleaning & Changing the
HEPA Dust Cup Filter
Warning:
Always unplug the unit from
electrical outlet before opening the Dust
Cup (container).
Important:
Do NOT use the HEPA filter
cartridge without the debris screen in
place.
Warning
After each Use - Always
:
remove the Filter Debris Screen from the
HEPA Dust Cup Filter, then vigorously
"TapClean" HEPA Filter until no more
dust can be removed.
IMPORTANT, Please Note : The
"TapClean" HEPA Dust Cup Filter &
Debris Screen will stop most of the tiniest
dust particles and airborne allergens from
re-entering the air you breathe. In fact it
stops 99.97% of all particles as small as
0.3 microns - many times smaller than a
human hair!!! Because of this incredible
filtration performance, the HEPA Dust Cup
Filter will quickly accumulate, inside the
white filter folds, many fine dust particles
that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. This can
cause the motor to overheat and the re-
settable thermostat to trip. (Should this
happen turn off the switch, unplug the unit
and allow unit to cool down. Clean the
HEPA Filter and Debris Screen as
described in this section, then reconnect
unit and proceed with vacuuming.)
1. To open the Dust Cup (container),
push the dust cup release button
and detach the Dust Cup
(container). (Fig. 1)
2. Pull out the HEPA Dust Cup Filter
or cloth dust cup filter. (Fig. 2)
Fig. 1
Fig.2
3. Empty the dust from the Dust Cup
(container).
4. Separate the debris screen from the
HEPA filter cartridge by grasping the
debris screen with one hand and the
filter frame with the other and pull
apart. (fig. 3)
Debris
Screen
Fig. 3
5. Vigorously "TapClean"
Fig. 4
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter. (Fig. 4)
6. "TapClean" the Debris
Screen or rinse under
a faucet until clean.
(Fig. 5) Remember
that the Debris Screen
must be completely
dry before reinstalling
in the vacuum.
7. Replace the Debris Screen on the
HEPA Dust Cup Filter and reinstall
filter assembly in the vacuum. (not
shown)
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
is properly
"TapCleaned"
after each use
Wash once a
and suction
month or when
suction
does not return
appears
to 100%, then
reduced.
we suggest that
Warning:
the HEPA filter
hours for drying before
be "TapCleaned"
replacing in unit.
vigorously until no
more dust can be removed, then
rinsed under the faucet and allowed to
dry for 24 hours before refitting into
the vacuum. (Fig. A) Wash once a
month or when suction appears
reduced.
CAUTION
: The suction hole must be
open, free of any obstructions at all
times. Otherwise, the motor will overheat
and could become damaged.
4
HEPA Filter
Fig. 5
Debris
Screen
Fig. A
Allow 24