Euro-Pro BIG SHARK V1505 Manuale d'uso - Pagina 4

Sfoglia online o scarica il pdf Manuale d'uso per Aspirapolvere Euro-Pro BIG SHARK V1505. Euro-Pro BIG SHARK V1505 4. 120v., 60hz., 7.5 amps

Stampa la pagina

OPERATING INSTRUCTIONS

Warning:

Always unplug from

electrical outlet before opening the dust

cup (container).

Note

: HEPA dust cup filter must be

used when operating the hand vacuum.

Using The Unit As A Hand

Vacuum

1. To open the dust cup (container), push

the dust cup release button and pull

out the dust cup. Verify that the HEPA

dust cup filter is inside, then re-attach

the dust cup (container) to the hand

vacuum.

2. To use the Hand Vacuum

with the shoulder strap,

attach it to the unit as

shown below.

3. To attach the crevice tool or oval

brush to the Hand Vacuum, push

brush into the suction hole, as

shown below.

4. To use the flexible hose, push the

smaller end of the hose into the

suction hole, then attach the desired

accessory to the other end of the

flexible hose, as shown below.

How To Operate Your

Hand Vacuum

1. Hold the hand vacuum firmly in

your hand by the Handle.

2. Push the On/Off Power Switch to

"On" position.

3. Start vacuuming.

CAUTION:

The Hand Vacuum is a

very powerful unit. Make sure that you

hold it firmly, otherwise it can slip out of

your hand and cause injury.

Intelli-Sense

Filter Monitor

When the Intelli-Sense

Filter

Monitor lights up, it means that the

dust cup is full or filter needs

cleaning. You must empty the dust

from the dust cup and clean the

HEPA dust cup filter right away.

OPERATING INSTRUCTIONS cont.

Cleaning & Changing the

HEPA Dust Cup Filter

Warning:

Always unplug the unit from

electrical outlet before opening the Dust

Cup (container).

Important:

Do NOT use the HEPA filter

cartridge without the debris screen in

place.

Warning

After each Use - Always

remove the Filter Debris Screen from the

HEPA Dust Cup Filter, then vigorously

"TapClean" HEPA Filter until no more

dust can be removed.

IMPORTANT, Please Note : The

"TapClean" HEPA Dust Cup Filter &

Debris Screen will stop most of the tiniest

dust particles and airborne allergens from

re-entering the air you breathe. In fact it

stops 99.97% of all particles as small as

0.3 microns - many times smaller than a

human hair!!! Because of this incredible

filtration performance, the HEPA Dust Cup

Filter will quickly accumulate, inside the

white filter folds, many fine dust particles

that are difficult to see but which will

eventually block or reduce your suction

power - if not cleaned properly. This can

cause the motor to overheat and the re-

settable thermostat to trip. (Should this

happen turn off the switch, unplug the unit

and allow unit to cool down. Clean the

HEPA Filter and Debris Screen as

described in this section, then reconnect

unit and proceed with vacuuming.)

1. To open the Dust Cup (container),

push the dust cup release button

and detach the Dust Cup

(container). (Fig. 1)

2. Pull out the HEPA Dust Cup Filter

or cloth dust cup filter. (Fig. 2)

Fig. 1

Fig.2

3. Empty the dust from the Dust Cup

(container).

4. Separate the debris screen from the

HEPA filter cartridge by grasping the

debris screen with one hand and the

filter frame with the other and pull

apart. (fig. 3)

Debris

Screen

Fig. 3

5. Vigorously "TapClean"

Fig. 4

the HEPA Dust Cup

Filter on a hard

surface until no more

dust is observed

falling out from

between the pleats of

the filter. (Fig. 4)

6. "TapClean" the Debris

Screen or rinse under

a faucet until clean.

(Fig. 5) Remember

that the Debris Screen

must be completely

dry before reinstalling

in the vacuum.

7. Replace the Debris Screen on the

HEPA Dust Cup Filter and reinstall

filter assembly in the vacuum. (not

shown)

PLEASE NOTE: The white pleated

filter material in the HEPA Dust Cup

Filter will discolor over time -This is

NORMAL and will NOT affect the

performance of the filter. If the HEPA

Dust Cup Filter

is properly

"TapCleaned"

after each use

Wash once a

and suction

month or when

suction

does not return

appears

to 100%, then

reduced.

we suggest that

Warning:

the HEPA filter

hours for drying before

be "TapCleaned"

replacing in unit.

vigorously until no

more dust can be removed, then

rinsed under the faucet and allowed to

dry for 24 hours before refitting into

the vacuum. (Fig. A) Wash once a

month or when suction appears

reduced.

CAUTION

: The suction hole must be

open, free of any obstructions at all

times. Otherwise, the motor will overheat

and could become damaged.

HEPA Filter

Fig. 5

Debris

Screen

Fig. A

Allow 24