AmerTac Westek BL-BR33M-SW Manual del usuario

Navegue en línea o descargue pdf Manual del usuario para Luminaria AmerTac Westek BL-BR33M-SW. AmerTac Westek BL-BR33M-SW 2 páginas. Wireless motion activated under cabinet light

Imprimir página

BL-BR33M-SW Owner's Manual

Location of Controls

1. Motion Sensor

2. Light Sensor

3. Motion Sensor Activation/

Manual On/Off Switch

4. 6 Super Bright LEDs

5. Battery Compartment*

OPERATING DIRECTIONS

Motion Sensor – Once batteries are installed:

Product includes an automatic light sensor that allows Motion Sensor to only operate at night or

in dark conditions. The light features an optional Motion Sensor which when activated will turn

the light ON automatically when motion is detected. The light will shut OFF automatically, after

30 or 60 seconds when no motion is detected. It detects motion approximate between 8.2 feet

(2.5m) and 11.5 feet (3.5M) of the motion sensor. To use this feature, simply slide the switch to the

desired location (30s / 60s).

OFF –Light will OFF.

ON – Motion sensor is inactive. Light will ON continuously.

30s – Light will turn OFF after 30 seconds if no motion is detected.

60s – Light will turn OFF after 60 seconds if no motion is detected.

MOUNTING INSTRUCTIONS

Magnetic Mounting (preferred)

The magnetic sections on the back of the light can be adjusted left to right so the corresponding

metal plates can be placed in the most ideal location for your installation.

Magnet option 1 - The metal plates come pre-drilled for easy front mounting on the desired

surface with included screws. Attached the fi rst plate to the overheads surface and check

location of second to make sure that sliding magnet will adhere to it.

Magnet option 2 - Remove protective cover from one side of the double-sided adhesive pad.

Place in center of the metal mounting plate. Do this for both metal-mounting plates. Place the

metal mounting plate with the adhesive pad onto the magnets located on the back side of

the light. Adhesive side placed away from the product (so it can stick into mounting position).

Do this for both metal-mounting plates. Remove second protective cover from adhesive tape

and place against desired surface. The metal mounting plate should be adhered to the desired

surface.

This is permanent tape that may cause damage if removed. Not recommended for use on

wallpaper or delicate surfaces.

Pulling on the light after the plates are properly installed should disconnect the metal mounting

plate from the magnets to allow for changing of batteries. The light should easily be able t o re

attached as the magnets and plates will draw to each other.

If you plan on using the light on a metal/magnetic surface, such as a cabinet, you may not need

to install the plates at all

Screw Mounting (optional)

1. Remove 2 metal plates & 2 3M Adhesive tapes from the 2 magnets on the back of the light.

2. Use Wall Anchors (not included) if securing to dry wall.

3. Measure two holes 6.75" (171 mm) apart. Drill two holes into mounting surface, insert wall

anchors (not included) and insert screws.

4. Leave screw heads out slightly so they can be inserted into the mounting holes located on

the back of the light.

5. Align and insert screw heads into mounting holes. Once inserted, slide the light onto the

screw heads to secure its position.

Limited Warranty

Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited

express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The

Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions

explained fully in the Limited Warranty on the website.

6. Magnets*

7. Slide Brackets*

8. Metal Plates*

9. 3M Adhesive Pads

**On back of unit

WIRELESS MOTION ACTIVATED

UNDER CABINET LIGHT

Product Dimensions:

Under Cabinet Light Size - 13.375" (H) x 2.25"(W) x 0.75"(D) / (340 mm x 56 mm x 19.3 mm)

INDOOR, DRY USE ONLY

BATTERY

Each Under Cabinet Light requires 3 AA batteries (not included).

INSERT/REPLACING THE BATTERIES

UNDER CABINET LIGHT – 3 AA batteries

If the LEDs appear to be dim this is an indication that the batteries need to be replaced.

Slide off the battery compartment.

Remove old batteries if replacing batteries.

Insert three new AA batteries.

Make sure to follow battery polarity guide when installing new batteries.

Replace battery compartment housing.

This product contains a button cell. If swallowed, it could cause severe injury or death in just 2

hours. Seek medical attention immediately.

SAFETY INFORMATION

Battery Precautions:

1. Use only the size and type of batteries specifi ed.

2. Always purchase the correct size and grade of battery most suitable for the intended use.

3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery

compartment.

Reversed batteries may cause damage to the device.

4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.

5. Replace all batteries of a set at the same time. Do not mix old and new batteries.

6. Clean the battery contacts and also those of the device prior to battery installation.

7. Do not dispose of batteries in fi re.

8. Remove batteries if consumed or if product is to be left unused for an extended period of

time.

250 Boulder Dr.

Breinigsville, PA 18031

610-336-1330

www.amertac.com

Made in China / Fabriqué en

Chine / Fabricado en China

I18-0033-B