Draper Access Instrucciones de instalación y funcionamiento
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Pantalla de proyección Draper Access. Draper Access 2 páginas. Electric projection screen
También para Draper Access: Instrucciones de instalación y funcionamiento (4 páginas)
Access/Series M Projection Screen by Draper
➀ Read instructions through completely before proceeding.
➁ Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂ Entire bottom of screen case should be unobstructed to permit access
to bottom panel for servicing.
➃ Screen should be installed level (using a carpenter's level).
➄ Nothing should be fastened to screen dowel or viewing surface.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
When locating viewing surface and checking clearance for screen's operation,
remember surface is centered in the length of the case. Regardless of
mounting method used, the following points apply:
➀ Mounting brackets are packed separately in carton. Engage each bracket
with top of housing as shown below and tighten set screws. A bracket
should be within 18" of each end of screen case. Brackets can be
removed and case mounted with lag screws through top of case (holes
drilled on site).
➁ Screen should be positively and securely supported so that vibration or
even abusive pulling on viewing surface will not weaken installation.
➂ Installer must insure that fasteners used are of adequate strength and
suitable for the mounting surface chosen. Supporting hardware (chains,
cables, rods, etc.) must be essentially vertical.
➃ Entire bottom of case must be readily accessible after installation is
complete.
➄ Front, back and top of case must be straight—not forced to warp or bow.
➅ If case is painted on location, removal of roller/fabric assembly is recom-
mended prior to painting. If not removed, slot on bottom of case should be
shielded to protect viewing surface from paint splatters or overspray.
Threaded rod
by others
3
1
/
"
16
8"
Copyright © 2002 Draper Inc.
Installation/Operating Instructions
Caution
7
3
/
"
16
5
6
/
"
8
7
7
/
"
16
1"
Form AccessM_Inst02
Bottom Access Panel Installation/Removal
Bottom access panel hooks over the lower inside edge of the screen housing
and then is pivoted downward until the engagement brackets on each end of
the bottom panel click into place with the ball detents on each endcap. Make
sure bottom access panel clicks in place at each end of its length.
With bottom access panel
angled up approx. 20 degrees,
engage hook on the panel
with lip of the housing
Remove bottom access panel by pushing up at each corner of panel adjacent
to slot in bottom of the housing.
With bottom access panel angled up approximately at 20° it can be lifted off of
the lip of the housing and then lowered out of the housing completely.
Spring Roller/Fabric Installation
The bottom access panel must be removed first.
The spear end mounting bracket has rectangular openings for accepting roller
spear. Back out the four set screws in bracket until they are flush with top side
of bracket.
¾"
To engage the spear end bracket flange above the two channels in the top of
the screen housing, rotate the bracket approximately 45° counterclockwise to
allow the top surface of the motor bracket to rest flat against the top inside of
the housing. Rotating the bracket clockwise until it is engaged with the
channels, slide it along the length of the housing toward the left end of
housing, leaving approximately
Tighten the four set screws on the bracket flange using
Engage the idler end bracket (nylon bushing) in the same manner as the
spear end bracket and slide it toward the opposite end of the screen housing.
Do not tighten the set screws on this bracket until the roller/fabric assembly is
installed.
Printed in U.S.A.
Using the hook and lip as a pivot,
pull the panel downward until the
engagement brackets click into
place with the ball detent
on each endcap
Engagement bracket
(one on each end of the
bottom access panel)
Bottom flange of Access housing
Bottom access panel pushup
points for panel removal
Access case as seen from below
3
/
" clearance between bracket and endcap.
4
1
/
" hex key.
8