Draper Access Инструкции по установке и эксплуатации

Просмотреть онлайн или скачать pdf Инструкции по установке и эксплуатации для Проекционный экран Draper Access. Draper Access 2 страницы. Electric projection screen
Также для Draper Access: Инструкции по установке и эксплуатации (4 страниц)

Печатать страницу

Access/Series M Projection Screen by Draper

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

➂ Entire bottom of screen case should be unobstructed to permit access

to bottom panel for servicing.

➃ Screen should be installed level (using a carpenter's level).

➄ Nothing should be fastened to screen dowel or viewing surface.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Hanging Screen

When locating viewing surface and checking clearance for screen's operation,

remember surface is centered in the length of the case. Regardless of

mounting method used, the following points apply:

➀ Mounting brackets are packed separately in carton. Engage each bracket

with top of housing as shown below and tighten set screws. A bracket

should be within 18" of each end of screen case. Brackets can be

removed and case mounted with lag screws through top of case (holes

drilled on site).

➁ Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface will not weaken installation.

➂ Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Supporting hardware (chains,

cables, rods, etc.) must be essentially vertical.

➃ Entire bottom of case must be readily accessible after installation is

complete.

➄ Front, back and top of case must be straight—not forced to warp or bow.

➅ If case is painted on location, removal of roller/fabric assembly is recom-

mended prior to painting. If not removed, slot on bottom of case should be

shielded to protect viewing surface from paint splatters or overspray.

Threaded rod

by others

Installation/Operating Instructions

Caution

Form AccessM_Inst02

Bottom Access Panel Installation/Removal

Bottom access panel hooks over the lower inside edge of the screen housing

and then is pivoted downward until the engagement brackets on each end of

the bottom panel click into place with the ball detents on each endcap. Make

sure bottom access panel clicks in place at each end of its length.

With bottom access panel

angled up approx. 20 degrees,

engage hook on the panel

with lip of the housing

Remove bottom access panel by pushing up at each corner of panel adjacent

to slot in bottom of the housing.

With bottom access panel angled up approximately at 20° it can be lifted off of

the lip of the housing and then lowered out of the housing completely.

Spring Roller/Fabric Installation

The bottom access panel must be removed first.

The spear end mounting bracket has rectangular openings for accepting roller

spear. Back out the four set screws in bracket until they are flush with top side

of bracket.

¾"

To engage the spear end bracket flange above the two channels in the top of

the screen housing, rotate the bracket approximately 45° counterclockwise to

allow the top surface of the motor bracket to rest flat against the top inside of

the housing. Rotating the bracket clockwise until it is engaged with the

channels, slide it along the length of the housing toward the left end of

housing, leaving approximately

Tighten the four set screws on the bracket flange using

Engage the idler end bracket (nylon bushing) in the same manner as the

spear end bracket and slide it toward the opposite end of the screen housing.

Do not tighten the set screws on this bracket until the roller/fabric assembly is

installed.

Printed in U.S.A.

Using the hook and lip as a pivot,

pull the panel downward until the

engagement brackets click into

place with the ball detent

on each endcap

Engagement bracket

(one on each end of the

bottom access panel)

Bottom flange of Access housing

Bottom access panel pushup

points for panel removal

Access case as seen from below

" clearance between bracket and endcap.

" hex key.