Draper Cinefold Instrucciones de montaje - Página 2
Navegue en línea o descargue pdf Instrucciones de montaje para Pantalla de proyección Draper Cinefold. Draper Cinefold 2 páginas. Cinefold portable projection screen
También para Draper Cinefold: Especificaciones (1 páginas), Instrucciones de montaje (2 páginas)
Imprimir página
Truss-Style Cinefold Portable Projection Screen by Draper
Read instructions through completely before proceeding; retain for
future reference.
Handle viewing surface with care; do not allow it to come in contact
with sharp or dirty objects.
Use Handy Cranks provided; failure to do so may lead to screen
damage.
Make sure screen is level.
Do not write on viewing surface.
Truss Assembly
Remove pouch containing viewing surface from case and set aside.
Remove and retain case divider, and take out all aluminum assemblies.
Unfold all folded aluminum assemblies completely, noting labels and color-
coded marks. Lock all hinges. Position Stage Right and Stage Left
sections in appropriate positions with snaps facing up . Top and Bottom
sections should be set with snaps facing down .
To increase frame rigidity, hinges on top and bottom frame sections have
rivnuts marked with red and green. Insert a Handy Crank through the
threadless rivnut (red) and tighten into the threaded rivnut (green).
Apply small sections marked "Stiffener Bars" to back of Bottom frame
section, using 8 Handy Cranks each. Failure to use all Handy Cranks may
result in damage to screen frame. Turn Bottom frame section over so
snaps face up.
If your screen frame is less than 25' wide, repeat step 4 for Top frame
section. Frames 25' wide and over are equipped with a special full-width
Stiffener for the top frame section. To attach it, place Stiffener flat with
green rivnuts face down. Place top frame section on top of and at right
angles to Stiffener, over the green rivnuts. Insert and tighten standard
Handy Cranks. Install 45° angle braces to the Top frame section and
Stiffener with short Handy Cranks. Turn Top frame so snaps face up.
Anti-Sway
Stabilizers
Heavy-Duty
Legs
411 S. Pearl St., Spiceland, IN 47385 USA 765-987-7999 fax 765-987-7142
e-mail [email protected]
Copyright © 2002 Draper, Inc. Form Cinefold_Inst02
Assembly Instructions
Caution
Rigid
Truss
Frame
Frame & Legs
Assemble with
Handy Cranks
www.draperinc.com
Printed in U.S.A.
Join Top and Bottom to Stage Right and Stage Left, using 2 Handy Cranks
on each of the 4 corners. Match numbers on white labels, and keep in
mind that no Handy Crank should protrude outside screen frame.
Remove surface from pouch. With the row of male snaps at bottom,
position screen surface over frame. Snap each of the 4 corners, then snap
across bottom, up sides, and across top.
Attach feet to inner side of legs with Handy Cranks, matching color-coded
markings. Attach legs to Stage Right and Stage Left with Handy Cranks,
matching colored tapes.
Raise screen to a vertical position. Add Heavy-Duty Legs and Anti-Sway
Stabilizers with Handy Cranks in the positions indicated below.
Handy Crank
Valance Bar
Drapery
Bar
Adjustable Skirt Bar
Dress-Up Kit Assembly
PLEASE NOTE: All components are labeled and color coded to
facilitate assembly.
A. Valance Bar attaches to frame with simple bayonet-style mounting.
B. Draper Bars mount to Valance Bar, bayonet-style.
C. Optional adjustable Skirt Bar is secured to frame at desired level with
positive-locking plunger mechanism. If Skirt Bar is not used, Skirt may
be snapped to bottom of viewing surface.
D. Valance, Drapes, and Skirt snap onto Mounting Bars.
Drapery
Bar