Draper Cinefold 조립 지침 - 페이지 2

{카테고리_이름} Draper Cinefold에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Draper Cinefold 2 페이지. Cinefold portable projection screen
Draper Cinefold에 대해서도 마찬가지입니다: 사양 (1 페이지), 조립 지침 (2 페이지)

페이지 인쇄

Truss-Style Cinefold Portable Projection Screen by Draper

Read instructions through completely before proceeding; retain for

future reference.

Handle viewing surface with care; do not allow it to come in contact

with sharp or dirty objects.

Use Handy Cranks provided; failure to do so may lead to screen

damage.

Make sure screen is level.

Do not write on viewing surface.

Truss Assembly

Remove pouch containing viewing surface from case and set aside.

Remove and retain case divider, and take out all aluminum assemblies.

Unfold all folded aluminum assemblies completely, noting labels and color-

coded marks. Lock all hinges. Position Stage Right and Stage Left

sections in appropriate positions with snaps facing up . Top and Bottom

sections should be set with snaps facing down .

To increase frame rigidity, hinges on top and bottom frame sections have

rivnuts marked with red and green. Insert a Handy Crank through the

threadless rivnut (red) and tighten into the threaded rivnut (green).

Apply small sections marked "Stiffener Bars" to back of Bottom frame

section, using 8 Handy Cranks each. Failure to use all Handy Cranks may

result in damage to screen frame. Turn Bottom frame section over so

snaps face up.

If your screen frame is less than 25' wide, repeat step 4 for Top frame

section. Frames 25' wide and over are equipped with a special full-width

Stiffener for the top frame section. To attach it, place Stiffener flat with

green rivnuts face down. Place top frame section on top of and at right

angles to Stiffener, over the green rivnuts. Insert and tighten standard

Handy Cranks. Install 45° angle braces to the Top frame section and

Stiffener with short Handy Cranks. Turn Top frame so snaps face up.

Anti-Sway

Stabilizers

Heavy-Duty

Legs

411 S. Pearl St., Spiceland, IN 47385 USA 765-987-7999 fax 765-987-7142

e-mail [email protected]

Assembly Instructions

Caution

Rigid

Truss

Frame

Frame & Legs

Assemble with

Handy Cranks

www.draperinc.com

Printed in U.S.A.

Join Top and Bottom to Stage Right and Stage Left, using 2 Handy Cranks

on each of the 4 corners. Match numbers on white labels, and keep in

mind that no Handy Crank should protrude outside screen frame.

Remove surface from pouch. With the row of male snaps at bottom,

position screen surface over frame. Snap each of the 4 corners, then snap

across bottom, up sides, and across top.

Attach feet to inner side of legs with Handy Cranks, matching color-coded

markings. Attach legs to Stage Right and Stage Left with Handy Cranks,

matching colored tapes.

Raise screen to a vertical position. Add Heavy-Duty Legs and Anti-Sway

Stabilizers with Handy Cranks in the positions indicated below.

Handy Crank

Valance Bar

Drapery

Bar

Adjustable Skirt Bar

Dress-Up Kit Assembly

PLEASE NOTE: All components are labeled and color coded to

facilitate assembly.

A. Valance Bar attaches to frame with simple bayonet-style mounting.

B. Draper Bars mount to Valance Bar, bayonet-style.

C. Optional adjustable Skirt Bar is secured to frame at desired level with

positive-locking plunger mechanism. If Skirt Bar is not used, Skirt may

be snapped to bottom of viewing surface.

D. Valance, Drapes, and Skirt snap onto Mounting Bars.

Drapery

Bar