Draper Paragon Instrucciones de instalación y funcionamiento
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Pantalla de proyección Draper Paragon. Draper Paragon 2 páginas. 220v electric screen
También para Draper Paragon: Especificaciones (2 páginas), Instrucciones de instalación y funcionamiento (2 páginas), Instrucciones de instalación y funcionamiento (2 páginas)
Imprimir página
These Installation/Operating Instructions are available in the offi cial language
of the country where you purchase the product. Please contact your distributor
to request a copy.
Vous pourriez demander les instructions d'installation et d'opération traduises
dans la langue offi cielle du pays ou vous achetez le produit. Veuillez
demander à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der
offi ziellen Sprache des Landes, indem Sie das Produkt gekauft haben,
vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.
➀
Read instructions through completely before proceeding.
➁
Follow instructions carefully. Installation con trary to in struc tions invali-
dates warranty.
➂
Pick up screen case from ends only. Picking case up at other
points will damage case and may damage fabric.
➃
Entire bottom of screen case should be unobstructed to permit
access to bottom panel for making electrical connections or servicing.
➄
Screen should be installed level (using a carpenter's level).
➅
Operating switch(es) packed separately in screen carton. Do not
discard with packing material.
➆
Screen operates on 220 V AC, 50 Hz., 1ph. current.
NOTE: Screen has been thoroughly inspected and tested at factory and found
to be operating properly prior to shipment.
Mounting Screen
Regardless of mounting method used, the following points apply:
➀ Screen should be lifted into position only by the end mounting brackets.
Draper provides eyebolts to use in hoisting the screen. Keep case
level by lifting end plates simultaneously to prevent surface damage.
Never attempt to lift screen along its length.
➁ Screen should be positively and securely supported so that vibration or
even abusive pulling will not weaken in stal la tion.
➂ Installer must insure that fasteners used are of adequate strength and
suitable for the mounting surface chosen. Installer must also insure that
wall or ceiling structure are of adequate strength. Supporting hardware
(chains, cables, rods, etc.) must be essentially vertical.
➃ Entire bottom of case must be readily accessible after in stal la tion is
complete.
➄ Front, back and top of case must be straight—not forced to warp or bow.
Use threaded rod and support brackets to keep large cases from warping.
➅ Do not use case to support adjacent sections of ceiling.
➆ If optional ceiling fl ange trim kits are attached, use hardware provided.
➇ If case is painted, slots on bottom of case should be shielded to protect
viewing surface from paint splatters or overspray.
➈ Do not seal unit in ceiling until electrical connections have been made and
screen has been operated successfully.
Electrical Connections
Screen operates on 220 V AC, 50 Hz., 1ph. current.
Junction box is located just above the closure panel, at the motor end of
screen. To properly remove closure panel, two people should follow the steps
on page two of these instructions. The junction box access plate is held
closed with pan head screws and may be opened with a Phillips screwdriver.
Removal of access plate exposes red, black and white pigtail leads and green
internal ground wire per wiring diagram attached.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire connecting shade to switch(es) and switch(es) to power supply
®
Copyright © 2009 Draper Inc.
Form Paragon220V_Inst09
Installation/Operating Instructions
220V Paragon Electric Screen by Draper
Caution
Printed in U.S.A.
should be furnished by installer. Con nec tions should be made in ac cor dance
with attached wiring diagram, and wiring should comply with national and
local electrical codes.
All operating switches should be "off" before power is con nect ed.
When screen is fi rst operated, be cautious! Cycle unit down and up several
times to confi rm satisfactory operation.
220 V AC Single Station Control—3-position up-off-down switch per mits
op er a tion to be stopped at any point. Factory adjusted limit switches
au to mat i cal ly stop screen when fully down or fully up.
220 V AC Multiple Station Control (Not CE approved)—Switches are sim i lar
in ap pear ance to 220 V a.c. Single Station Control. Screen stops when switch
is re leased and may be re start ed in either direction. Factory adjusted limit
switch es stop screen automatically when fully up or fully down.
24V Control—Three-button up-stop-down switch(es) stop at any point
de sired, operate in any sequence. Factory adjusted limit switches
au to mat i cal ly stop screen when fully up or fully down. Installer should
incorporate an all-pole disconnect in the fi xed wiring.
Key Operated Switching (Not CE approved)—Two kinds of key-op er at ed
switches are op tion al ly available with this unit. ➀ The key-operated power
sup ply switch controls power to the screen and switch es. When it is "off",
the switches will not operate screen. Key may be removed from the switch in
either "on" or "off" position. ➁ A three-po si tion key switch per mits the screen
to be operated directly by key. In this case, the screen's operator must always
have a key.
RS232/Ethernet—Serial communication and network communication
optionally available with wall switches, RF or IR remote.
Screen has been factory set and should not nor mal ly require further
ad just ment. However, if you desire to change the "up" and "down" stopping
positions, proceed as follows:
CAUTION: Be sure all switches are in "off" position before adjusting limit
switches. Always be pre pared to shut screen off man u al ly when new
ad just ment is being tested. Screen may be se vere ly damaged if viewing
surface is al lowed to run too far up or too far down.
ADJUSTING "FULLY UP" POSITION—Put a small screw driver in the groove
of the yellow button on the motor and press vertically until hearing a "click".
Raise the shade by pressing the "up" switch on unit. Press the "stop" switch
when the screen is at the desired position. Then press the yellow button on
motor until you hear a "click", then release.
ADJUSTING "FULLY DOWN" POSITION—Put a small screw driver in the
groove of the white button on the motor and press vertically until hearing a
"click". Lower the screen by pressing the "down" switch on unit. Press the
"stop" switch when the screen is at the desired position. Then press the white
button on motor until you hear a "click", then release.
AT NO TIME SHOULD SCREEN BE UNROLLED ENOUGH TO EXPOSE
ANY PART OF SCREEN ROLLER.
3
/
" (9.5 mm) -16 threaded rod
8
(use for adjusting
deflection in extremely
long units) by others.
8"
337 mm
Knockouts for electrical connections
305 mm
(two per end) with plastic plugs
Please see back page for dimensional diagrams of case and op-
tional wall mounting bracket, wiring diagrams and in struc tions on
removing and replacing the bottom closure.
If you encounter any diffi culties installing or ser vic ing your Paragon screen, call your
dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-1689.
Operation
Adjustments
1
/
" (12.7 mm) threaded
2
rod (for suspending
screen) by others.
Eyebolts for hoisting screen
(do not lift screen by center of case).
Case support brackets.