投影スクリーン Draper ParagonのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Draper Paragon 2 ページ。 220v electric screen
Draper Paragon にも：仕様 (2 ページ), 設置および操作説明書 (2 ページ), 取付・取扱説明書 (2 ページ)

ページを印刷する

These Installation/Operating Instructions are available in the ofﬁ cial language

of the country where you purchase the product. Please contact your distributor

to request a copy.

Vous pourriez demander les instructions d'installation et d'opération traduises

dans la langue ofﬁ cielle du pays ou vous achetez le produit. Veuillez

demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der

ofﬁ ziellen Sprache des Landes, indem Sie das Produkt gekauft haben,

vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

➀

Read instructions through completely before proceeding.

➁

Follow instructions carefully. Installation con trary to in struc tions invali-

dates warranty.

➂

Pick up screen case from ends only. Picking case up at other

points will damage case and may damage fabric.

➃

Entire bottom of screen case should be unobstructed to permit

access to bottom panel for making electrical connections or servicing.

➄

Screen should be installed level (using a carpenter's level).

➅

Operating switch(es) packed separately in screen carton. Do not

discard with packing material.

➆

Screen operates on 220 V AC, 50 Hz., 1ph. current.

NOTE: Screen has been thoroughly inspected and tested at factory and found

to be operating properly prior to shipment.

Mounting Screen

Regardless of mounting method used, the following points apply:

➀ Screen should be lifted into position only by the end mounting brackets.

Draper provides eyebolts to use in hoisting the screen. Keep case

level by lifting end plates simultaneously to prevent surface damage.

Never attempt to lift screen along its length.

➁ Screen should be positively and securely supported so that vibration or

even abusive pulling will not weaken in stal la tion.

➂ Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Installer must also insure that

wall or ceiling structure are of adequate strength. Supporting hardware

(chains, cables, rods, etc.) must be essentially vertical.

➃ Entire bottom of case must be readily accessible after in stal la tion is

complete.

➄ Front, back and top of case must be straight—not forced to warp or bow.

Use threaded rod and support brackets to keep large cases from warping.

➅ Do not use case to support adjacent sections of ceiling.

➆ If optional ceiling ﬂ ange trim kits are attached, use hardware provided.

➇ If case is painted, slots on bottom of case should be shielded to protect

viewing surface from paint splatters or overspray.

➈ Do not seal unit in ceiling until electrical connections have been made and

screen has been operated successfully.

Electrical Connections

Screen operates on 220 V AC, 50 Hz., 1ph. current.

Junction box is located just above the closure panel, at the motor end of

screen. To properly remove closure panel, two people should follow the steps

on page two of these instructions. The junction box access plate is held

closed with pan head screws and may be opened with a Phillips screwdriver.

Removal of access plate exposes red, black and white pigtail leads and green

internal ground wire per wiring diagram attached.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting shade to switch(es) and switch(es) to power supply

Form Paragon220V_Inst09

Installation/Operating Instructions

220V Paragon Electric Screen by Draper

Caution

Printed in U.S.A.

should be furnished by installer. Con nec tions should be made in ac cor dance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be "off" before power is con nect ed.

When screen is ﬁ rst operated, be cautious! Cycle unit down and up several

times to conﬁ rm satisfactory operation.

220 V AC Single Station Control—3-position up-off-down switch per mits

op er a tion to be stopped at any point. Factory adjusted limit switches

au to mat i cal ly stop screen when fully down or fully up.

220 V AC Multiple Station Control (Not CE approved)—Switches are sim i lar

in ap pear ance to 220 V a.c. Single Station Control. Screen stops when switch

is re leased and may be re start ed in either direction. Factory adjusted limit

switch es stop screen automatically when fully up or fully down.

24V Control—Three-button up-stop-down switch(es) stop at any point

de sired, operate in any sequence. Factory adjusted limit switches

au to mat i cal ly stop screen when fully up or fully down. Installer should

incorporate an all-pole disconnect in the ﬁ xed wiring.

Key Operated Switching (Not CE approved)—Two kinds of key-op er at ed

switches are op tion al ly available with this unit. ➀ The key-operated power

sup ply switch controls power to the screen and switch es. When it is "off",

the switches will not operate screen. Key may be removed from the switch in

either "on" or "off" position. ➁ A three-po si tion key switch per mits the screen

to be operated directly by key. In this case, the screen's operator must always

have a key.

RS232/Ethernet—Serial communication and network communication

optionally available with wall switches, RF or IR remote.

Screen has been factory set and should not nor mal ly require further

ad just ment. However, if you desire to change the "up" and "down" stopping

positions, proceed as follows:

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches. Always be pre pared to shut screen off man u al ly when new

ad just ment is being tested. Screen may be se vere ly damaged if viewing

surface is al lowed to run too far up or too far down.

ADJUSTING "FULLY UP" POSITION—Put a small screw driver in the groove

of the yellow button on the motor and press vertically until hearing a "click".

Raise the shade by pressing the "up" switch on unit. Press the "stop" switch

when the screen is at the desired position. Then press the yellow button on

motor until you hear a "click", then release.

ADJUSTING "FULLY DOWN" POSITION—Put a small screw driver in the

groove of the white button on the motor and press vertically until hearing a

"click". Lower the screen by pressing the "down" switch on unit. Press the

"stop" switch when the screen is at the desired position. Then press the white

button on motor until you hear a "click", then release.

AT NO TIME SHOULD SCREEN BE UNROLLED ENOUGH TO EXPOSE

ANY PART OF SCREEN ROLLER.

" (9.5 mm) -16 threaded rod

(use for adjusting

deflection in extremely

long units) by others.

337 mm

Knockouts for electrical connections

305 mm

(two per end) with plastic plugs

Please see back page for dimensional diagrams of case and op-

tional wall mounting bracket, wiring diagrams and in struc tions on

removing and replacing the bottom closure.

If you encounter any difﬁ culties installing or ser vic ing your Paragon screen, call your

dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-1689.

Operation

Adjustments

" (12.7 mm) threaded

rod (for suspending

screen) by others.

Eyebolts for hoisting screen

(do not lift screen by center of case).

Case support brackets.