投影スクリーン Draper ParagonのPDF 設置および操作説明書をオンラインで閲覧またはダウンロードできます。Draper Paragon 2 ページ。 220v electric screen
Draper Paragon にも：仕様 (2 ページ), 取付・取扱説明書 (2 ページ), 取付・取扱説明書 (2 ページ)

ページを印刷する

➀

Read instructions through completely before proceeding.

➁

Follow instructions carefully. Installation con trary to in struc tions invali-

dates warranty.

➂

Pick up screen case from ends only. Picking case up at other

points will damage case and may damage fabric.

➃

Entire bottom of screen case should be unobstructed to permit

access to bottom panel for making electrical connections or servicing.

➄

Screen should be installed level (using a carpenter's level).

➅

Operating switch(es) packed separately in screen carton. Do not

discard with packing material.

➆

Screen operates on 110-120v, 60 Hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and found

to be operating properly prior to shipment.

Mounting Screen

Regardless of mounting method used, the following points apply:

➀ Screen should be lifted into position only by the end mounting brackets.

Draper provides eyebolts to use in hoisting the screen. Never attempt to

lift screen along its length.

➁ Screen should be positively and securely supported so that vibration or

even abusive pulling will not weaken in stal la tion.

➂ Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Installer must also insure that

wall or ceiling structure are of adequate strength. Supporting hardware

(chains, cables, rods, etc.) must be essentially vertical.

➃ Entire bottom of case must be readily accessible after in stal la tion is

complete.

➄ Front, back and top of case must be straight—not forced to warp or bow.

Use threaded rod and support brackets to keep large cases from warping.

➅ Do not use case to support adjacent sections of ceiling.

➆ If optional ceiling ﬂ ange trim kits are attached, use hardware provided.

➇ If case is painted, slots on bottom of case should be shielded to protect

viewing surface from paint splatters or overspray.

➈ Do not seal unit in ceiling until electrical connections have been made and

screen has been operated successfully.

Electrical Connections

Screen operates on 110-120v, 60 Hz. current.

Junction box is located just above the closure panel, at the motor end of

screen (left hand motor location only on Paragon). To properly remove closure

panel, two people should follow the steps on page two of these instructions.

The junction box access plate is held closed with pan head screws and may

be opened with a Phillips screwdriver. Removal of access plate exposes

red, black and white pigtail leads and green internal ground wire per wiring

diagram attached.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting shade to switch(es) and switch(es) to power supply

should be furnished by installer. Con nec tions should be made in ac cor dance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be "off" before power is con nect ed.

Installation/Operating Instructions

Paragon by Draper

Caution

Form Paragon_Inst04

When screen is ﬁ rst operated, be cautious! Cycle unit down and up several

times to conﬁ rm satisfactory operation.

110-120v SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch

permits operation to be stopped at any point. Factory adjusted limit switch es

automatically stop screen when fully down or fully up.

110-120v MULTIPLE STATION CONTROL—Switches are similar in

ap pear ance to 110-120v Single Station Control. Screen stops when switch

is re leased and may be re start ed in either direction. Factory adjusted limit

switches stop screen automatically when fully up or fully down.

24v MULTIPLE STATION CONTROL—Three-button UP-STOP-DOWN

switches stop at any point desired, operate in any sequence. Factory adjusted

limit switches automatically stop screen when fully up or fully down.

KEY OPERATED SWITCHING—Two kinds of key-operated switches are

optionally available with this unit.

➀ The key-operated power supply switch controls power to the screen and

switches. When it is "off", the switches will not operate screen. Key may be

removed from the switch in either "on" or "off" position.

➁ A three-position key switch permits the screen to be op er at ed directly by

key. In this case, the screen's operator must always have a key.

Screen has been factory set and should not nor mal ly require further

ad just ment. However, if you desire to change the "up" and "down" stopping

positions, proceed as follows:

CAUTION: Be sure all switches are in "off" position before adjusting limit

switches. Always be pre pared to shut screen off man u al ly when new

ad just ment is being tested. Screen may be se vere ly damaged if viewing

surface is al lowed to run too far up or too far down.

ADJUSTING "FULLY UP" POSITION—Put a small screw driver in the groove

of the yellow button on the motor and press vertically until hearing a "click".

Raise the shade by pressing the "up" switch on unit. Press the "stop" switch

when the screen is at the desired position. Then press the yellow button on

motor until you hear a "click", then release.

ADJUSTING "FULLY DOWN" POSITION—Put a small screw driver in the

groove of the white button on the motor and press vertically until hearing a

"click". Lower the screen by pressing the "down" switch on unit. Press the

"stop" switch when the screen is at the desired position. Then press the white

button on motor until you hear a "click", then release.

AT NO TIME SHOULD SCREEN BE UNROLLED ENOUGH TO EXPOSE

ANY PART OF SCREEN ROLLER.

" -16 threaded rod

(use for adjusting

deflection in extremely

long units) by others.

Knockouts for electrical connections

12"

*Left hand motor location only on Paragon

Please see back page for dimensional diagrams of case and optional

wall mounting bracket, wiring diagrams and in struc tions on removing

and replacing the bottom closure.

If you encounter any difﬁ culties installing or ser vic ing your Paragon

screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765)

987-7999; fax (765) 987-7142; or e-mail [email protected].

Printed in U.S.A.

Operation

Adjustments

" threaded

rod (for suspending

screen) by others.

Eyebolts for hoisting screen

(do not lift screen by center of case).

Case support brackets.

(two per end) with plastic plugs*