Draper FlexShade NEXD Instrucciones de instalación y funcionamiento - Página 5
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Mobiliario interior Draper FlexShade NEXD. Draper FlexShade NEXD 8 páginas. Clutch-operated small and large hardware
También para Draper FlexShade NEXD: Instrucciones de instalación y funcionamiento (6 páginas), Manual de instrucciones (8 páginas), Instrucciones de instalación y funcionamiento (8 páginas), Instrucciones de instalación y funcionamiento (10 páginas), Manual de instrucciones (12 páginas)
Imprimir página
Bottom-Up FlexShade
Small and Large Hardware
Section 6 -Idler End Safety Bracket
WARNING: If Shade is installed at a distance
from the window greater than the diameter of
roller assembly, Safety Bracket must be
installed on window side of Idler Endcap to
safely contain shade, BEFORE installing Shade
Roller Assembly and room side Safety Bracket.
1.
Install Safety
Bracket
(provided
in separate
to
packaging)
Idler Endcap.
!
If Fascia has
been ordered
with this shade,
attach Bracket
to Clutch Endcap
as well.
2.
Install BOTH C020.680
Screws to secure
Bracket.
!
If shade is jamb
mounted, install Bracket
at the same time as
mounting endcaps
A
B
Please Note: If installing shade or shades in an area where misuse is likely,
this fastening method should be used.
Section 7 - Hem Bar
1. Remove one of the endcaps from the fabric hem bar.
2. Remove fabric retainer from hem bar and insert it into
the fabric hem.
3. Attach the hem bar assembly to the fabric panel by
sliding it over the fabric and retainer, then re-attach the
hem bar endcap.
Caution: Do NOT remove the draw cable from the hem
bar assembly during installation. Doing so may require
that the hem bar assembly be disassembled to
re-install the cable.
NEXD,
®
Caution: Endcaps must be
fastened securely to mounting
surface and cannot move from
side to side.
If changes, differences, or
measurement errors occur on-site,
adjust product by utilizing slotted
holes in the endcap [A] to adjust
for zero gap between the fascia
and endcap covers.
Once these adjustments are made,
utilize round holes [B] to drive
additional screws for securing
position.
Figure 7
Section 8 - Pre-tensioning Bottom Roller
Please Note: The fabric retraction device must be pre-tensioned to 3-5 revolutions.
Caution: NEVER ROTATE THE SPEAR IN THE OPPOSITE DIRECTION
indicated by the arrows. If this happens, the springs MUST BE REPLACED.
Caution: DO NOT pre-tension the spring beyond 5 revolutions. Adding
rotations WILL NOT increase the retraction spring force on the assembly. The
mechanism is rated for a maximum of 25 revolutions throughout the operating
height of the shade. Up to 20 revolutions may be required for operation of the
unit, plus a maximum of 5 pre-rotations. Operating the fabric retraction device
beyond 25 revolutions may cause the device to fail, requiring replacement.
Figure 8-A
WHEN INSTALLING
INTO BRACKETS
1. Orient the triangular shaped arrow on the end of the device to point UP
. This ensures there are zero pre-rotations on the device.
(Fig. 8-A)
2. Holding the roller in this position, rotate spear counter-clockwise
(as indicated by the directional arrow)
allow it to slowly unwind clockwise until it stops.
Caution: Allowing the spear to unwind rapidly can damage the mechanism.
3. Ensure that the fabric panel is wound tightly around the roller assembly.
4. Orient the hem bar and the triangular shaped arrow on the end of the fabric
retraction device so that the arrow points down toward the ground
Please Note: The number of rotations required can be found on the order label.
5. Hold the spear with pliers in this position, and rotate the roller clockwise
. There will be a slight "click" as the spring assist
indicated by the directional arrow)
locks.
6. Hold roller with arrow pointing down, and use pliers to rotate the spear in a
counter-clockwise direction. The rotation will "lock" at each revolution by
rotating the spear just beyond one full revolution, then, allowing it to slowly
unwind until it stops at the point where the triangular shaped arrow is again
pointing downward. Repeat this until the mechanism has 3-5 pre-rotations.
Please Note: The device must remain locked until the final step
. Rotating the fabric roller as though the shade is being raised
are attached to roller)
will unlock the device. The installer should ensure that the hem bar cannot move
around the fabric roller if the roller is unlocked before the installation is complete.
WARNING: DO NOT OPEN. ASSEMBLY CONTAINS HIGHLY STRESSED
SPRINGS. UNIT IS NOT REPAIRABLE.
page 5 of 8
Figure 8-B
TO PRE-TENSION
approximately 1/4-turn. Restrain the spear and
(Fig. 8-B)
(when draw cables
.
(as