- ページ 5

室内装飾品 Draper FlexShade NEXDのPDF 説明書インストールと操作をオンラインで閲覧またはダウンロードできます。Draper FlexShade NEXD 8 ページ。 Clutch-operated small and large hardware
Draper FlexShade NEXD にも：取付・取扱説明書 (6 ページ), 取扱説明書 (8 ページ), 説明書インストールと操作 (8 ページ), 説明書インストールと操作 (10 ページ), 取扱説明書 (12 ページ)

ページを印刷する

Bottom-Up FlexShade

Small and Large Hardware

Section 6 -Idler End Safety Bracket

WARNING: If Shade is installed at a distance

from the window greater than the diameter of

roller assembly, Safety Bracket must be

installed on window side of Idler Endcap to

safely contain shade, BEFORE installing Shade

Roller Assembly and room side Safety Bracket.

Install Safety

Bracket

(provided

in separate

packaging)

Idler Endcap.

If Fascia has

been ordered

with this shade,

attach Bracket

to Clutch Endcap

as well.

Install BOTH C020.680

Screws to secure

Bracket.

If shade is jamb

mounted, install Bracket

at the same time as

mounting endcaps

Please Note: If installing shade or shades in an area where misuse is likely,

this fastening method should be used.

Section 7 - Hem Bar

1. Remove one of the endcaps from the fabric hem bar.

2. Remove fabric retainer from hem bar and insert it into

the fabric hem.

3. Attach the hem bar assembly to the fabric panel by

sliding it over the fabric and retainer, then re-attach the

hem bar endcap.

Caution: Do NOT remove the draw cable from the hem

bar assembly during installation. Doing so may require

that the hem bar assembly be disassembled to

re-install the cable.

NEXD,

Caution: Endcaps must be

fastened securely to mounting

surface and cannot move from

side to side.

If changes, differences, or

measurement errors occur on-site,

adjust product by utilizing slotted

holes in the endcap [A] to adjust

for zero gap between the fascia

and endcap covers.

Once these adjustments are made,

utilize round holes [B] to drive

additional screws for securing

position.

Figure 7

Section 8 - Pre-tensioning Bottom Roller

Please Note: The fabric retraction device must be pre-tensioned to 3-5 revolutions.

Caution: NEVER ROTATE THE SPEAR IN THE OPPOSITE DIRECTION

indicated by the arrows. If this happens, the springs MUST BE REPLACED.

Caution: DO NOT pre-tension the spring beyond 5 revolutions. Adding

rotations WILL NOT increase the retraction spring force on the assembly. The

mechanism is rated for a maximum of 25 revolutions throughout the operating

height of the shade. Up to 20 revolutions may be required for operation of the

unit, plus a maximum of 5 pre-rotations. Operating the fabric retraction device

beyond 25 revolutions may cause the device to fail, requiring replacement.

Figure 8-A

WHEN INSTALLING

INTO BRACKETS

1. Orient the triangular shaped arrow on the end of the device to point UP

. This ensures there are zero pre-rotations on the device.

(Fig. 8-A)

2. Holding the roller in this position, rotate spear counter-clockwise

(as indicated by the directional arrow)

allow it to slowly unwind clockwise until it stops.

Caution: Allowing the spear to unwind rapidly can damage the mechanism.

3. Ensure that the fabric panel is wound tightly around the roller assembly.

4. Orient the hem bar and the triangular shaped arrow on the end of the fabric

retraction device so that the arrow points down toward the ground

Please Note: The number of rotations required can be found on the order label.

5. Hold the spear with pliers in this position, and rotate the roller clockwise

. There will be a slight "click" as the spring assist

indicated by the directional arrow)

locks.

6. Hold roller with arrow pointing down, and use pliers to rotate the spear in a

counter-clockwise direction. The rotation will "lock" at each revolution by

rotating the spear just beyond one full revolution, then, allowing it to slowly

unwind until it stops at the point where the triangular shaped arrow is again

pointing downward. Repeat this until the mechanism has 3-5 pre-rotations.

Please Note: The device must remain locked until the final step

. Rotating the fabric roller as though the shade is being raised

are attached to roller)

will unlock the device. The installer should ensure that the hem bar cannot move

around the fabric roller if the roller is unlocked before the installation is complete.

WARNING: DO NOT OPEN. ASSEMBLY CONTAINS HIGHLY STRESSED

SPRINGS. UNIT IS NOT REPAIRABLE.

page 5 of 8

Figure 8-B

TO PRE-TENSION

approximately 1/4-turn. Restrain the spear and

(Fig. 8-B)

(when draw cables

(as