Anchor LIB-BP4 Manual del usuario - Página 4

Navegue en línea o descargue pdf Manual del usuario para Altavoces Anchor LIB-BP4. Anchor LIB-BP4 4 páginas. Anchor lib-6000hcu2

Imprimir página

BASIC SYSTEM OPERATION

NOTE: Fully Charge Batteries Before First Use!

1. Set all Input Level Controls to minimum & Tones Controls to flat

or the middle setting before turning your system on

2. Plug a wired microphone into the MIC 1 or MIC 2 jacks and/or

plug an audio source into the LINE-IN jack

3. Switch POWER to ON, the red BATTERY LED will light

4. Slowly increase the Level Control for the input jacks used to the

desired volume

5. Set SPEECH PROJECTION to ON for speech applications or

OFF for standard applications (music & indoor use)

6. Adjust BASS & TREBLE controls to desired sound quality

CARING FOR YOUR BUILT-IN BATTERIES

It is very important that you fully charge the batteries in your new sound system

before the first time its used. To preserve battery life it is also recommended

that batteries be fully charged as soon as possible after every use regardless of

the length of operation.

UNDERSTANDING THE BATTERY LEVEL INDICATOR

LED Flashing Red:

Battery charge is very low, in 15-30 minutes the Battery

Protection Circuit will turn the system off.

LED Off:

Battery is completely drained and must be charged.

NOTE: System Can Be Used While Batteries Charge!

OPERATING IN AC MODE

Plug your sound system into an AC outlet. Operate as normal while charg-

ing the built-in batteries at the same time. The Charger LED will light during

charging and flash when the battery is fully charged.

BATTERY SERVICE TIME

With the batteries fully charged you can expect approx.:

6-8 hrs @ Medium Volume

2-4 hrs @ Full Volume

Of continuous music input (longer for speech) . Service time will vary depend-

ing on control settings and use of accessories (built-in CD player, wireless

receivers and/or a companion speaker).

IMPORTANT: Always Store Your System w/

Batteries Fully Charged!

SYSTEM STORAGE & BATTERIES

Always store your sound system with the batteries fully charged. For extended

periods of storage leave the system plugged into an AC outlet. If this is not pos-

sible, charge the system at least once each month for a minimum of 24 hours.

WIRELESS RECEIVER CONTROLS

(see page 6)

INPUT LEVEL CONTROLS

UNIVERSAL MIC - INPUT JACKS

Balanced XLR - low impedance, for bal-

anced mic, powers condenser-type mics

Unbalanced 1/4" - high impedance, for

unbalanced mics, no phantom power

LINE IN - INPUT JACK

Unbalanced 1/4" - high impedance, for

any line-level signal source: cassette/

VCR/CD/DVD players, musical instru-

ments, 2nd sound system or . . .

SPEECH/PROJECTION SWITCH

SPEAKER OUTPUT

When using Switched Speaker Output

LIBERTY SOUND SYSTEM

the Liberty's internal speakers are

disconnected

CONTROL PANEL

Model Shown: LIB-6000HCU2

CHARGING YOUR BUILT-IN BATTERIES

An automatic charging system is built-in to your Liberty Sound System. It is designed to properly charge and

maintain the systems built-in batteries. To charge batteries:

1. Plug the power cord into your sound system

2. Plug the other end of the cord into AC outlet

Charger LED will stay on during charging

When in AC mode the system automatically transfers power from the battery charger to the power amplifier at

high volume output, causing the Charger LED to flicker.

3. Batteries will fully charge in approx. 6-8 hrs

Charger LED will flash

CD PLAYER CONTROLS

(see page 6)

CD PLAYER VOLUME CONTROL

TONE LEVEL CONTROLS

LINE OUT - OUTPUT JACK

Unbalanced 1/4" - provides a combined

output of all active system inputs

Record your presentation or connect to

another powered sound system

(Output is post source level; any volume

fluctuations for a specific input will affect

this output signal level)

BATTERY CHARGER INDICATOR

12 VOLT DC - OUTPUT JACK

Power for auxiliary equipment:

outboard wireless receiver or Anchor

Audio's Mini-Mix

BATTERY LEVEL INDICATOR

POWER SWITCH

SPEECH PROJECTION SWITCH SETTINGS

Allows you to customize the sound output of your Liberty

system for specific applications:

Speech Projection Off (button out): A flat, full range

frequency response for music or indoor voice applications.

Speech Projection On (button in): Frequencies in the

vocal range are boosted for added clarity and efficient sound

projection. Use this setting for outdoor functions, large

crowds and speech applications.